(ESC) Drone Speed Controller

1. Item:30A brushed ESC
2. Voltage support: 4~8V.
3. Forward 30A
4. UBEC output: voltage 5.7V, current 1A.

1. Support High Voltage (HV) Receivers
2. Input voltage: 3.7V-27V
3. Max current: 30A
4. 18AWG silicone cable
5. JST Plug
6. Cable length 20cm
7. Weight: 11g – With LED indicator lamp

1. Brand: Ready to sky
2. Model: ReadytoSky 2-6S 40A
3. Current: 40A
4. Burst Current(10sec): 60A
5. Weight: 26g

1. Brand: Ready to sky
2. Model: 40A 2-6S ESC
3. Current: 40A
4. Burst Current(10sec): 60A
5. Programming: Timing(high/middle)

1. Product: Bidirectional 50A 2-6s UBEC 5A 5V
2. Input voltage: 5V
3. Frequency PWM: 1000-2000us
4. Peak Current (A): 50

1. Type: 4 in 1
2. Current: 15A
3. Peak Current (10s): 20A
4. BEC: 5V

1. Product: Cyclone 20A BLHeil_S 20A ESC
2. Input Voltage: 2-4S Lipo
3. BEC Output: None
4. Working current: 20A (maximum current: 25A 10S)
5. Processor: SLABS

1. Model: FrSky Smart Port RPM and Temperature Sensor
2. Operating Voltage Range: 4 -10 V DC
3. Current consumption: 25mA@5V
4. Measures RPM: 1,000-30,000 rpm
5. Measures temperature: 20-250°C

1. Product: HENGE 8A UBEC
2. Provide large output current
3. Overcurrent and overheat protection function
4. The max efficiency of the chip is up to 93%

1. Waterproof and dustproof, suitable for races in all weather conditions.
2. Small size with built-in capacitor module.
3. Fwd/Rev/Br running mode fits various vehicles (Fwd =Forward, Br=Brake, Rev=Reverse).
4. Great current endurance capability.
5. Great built-in BEC output capacity.

1 Output: Continuous 80A, Burst 100A up to 10 seconds.
2 Input Voltage: 2-6S Lipo, 5-18 cells NiMH.
3 BEC: 5A / 5V Switch mode BEC.
4 Refresh rate of the throttle signal: 50Hz to 432Hz.
5 Max Speed: 210000rpm for 2 Poles BLM, 70000rpm for 6 poles BLM, 35000rpm for 12 poles BLM.
(BLM = BrushLess Motor)

1. Continuous Current: 40A
2. Burst Current: 55A (10 Sec.)
3. BEC Mode: Linear Mode, 5V@3A
4. Programmable: Yes
5. Battery cell : Li-PO / NiMH

1. Output: Continuous 50A
2. Burst 65A up to 10 seconds.
3. Input Voltage: 2-4S Lipo, 5-12 cells N
4. BEC: 5A / 5V Switch mode BEC.
5. The refresh the rate of the throttle signal: 50Hz to 432

1. Model Number:XRotor-40A
2. Cont.Current:40A
3. Burst Current(10sec):60A
4. BEC:None
5. Lipo:2-6S
6. Programming:Timing (high/middle)
7. Weight:26g

1. MCU – STM32H743 32-bit processor running at 480 MHz
2. IMU – MPU6000
3. Barometer – BMP280
4. OSD – AT7456E
5. Onboard Bluetooth chip – ESP32-C3

1. Input: 2-5S input Maximum input 6S (close brake)
2. 32bit architecture
3. Telemetry capability (voltage, current, temperature, speed)
4. All inputs and outputs are protected against overvoltage (~30V) and under voltage (~-30V). 3,3 and 5V capable
5. Supports all common Dshot commands like Turtle Mode, 3D mode and change of rotation
6. Overcurrent protection (measures the current and reduces it to max. 40A)

1. Model: Wp-1060-BRUSHED
2. Voltage Range: 2-3S Lipo or 5-9 NiMH
3. Resistance: Fwd 0.001Ω, Rev 0.002Ω
4. BEC Output: 3A/5V (Linear Mode)
5. PWM Frequency: 1KHz

1. Cont Current: 30A
2. Burst Current: 35A
3. BEC Model: Linear mode
4. Using Multi integrated circuit opted special program,
5. Fast throttle response
6. Firmware was optimized specific integrated circuit ally for disc motor, and it has a very good compatibility