This is an Holybro Pixhawk 4 Mini Autopilot Flight Controller. This Fight Controller is designed for working with smaller drones. Pixhawk 4 Mini takes the FMU processor and memory resources from the Pixhawk 4 while eliminating normally unused interfaces. This allows the Pixhawk 4 Mini to be small enough to fit in a 250mm racer drone. This Flight Controller is Easy to Install.

NOTE: This Flight Controller package doesn’t include a GPS module. 

Features:

1. Aluminum casing for great thermal performance.
2. Easy to connect to commercial ESCs.
3. Pre-installed with the most recent PX4 firmware.
4. Used in Most of the Mini drones.

Package Includes:

1 x Holybro Pixhawk 4 Mini Autopilot Flight Controller

PM02 is a simple way of providing your APM and Pix32 with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.2V and a maximum of 3A from up to a 12S LiPo battery. The Power Module comes completely assembled with XT60 connectors, and wrapped in shrink tubing for protection.
The Power Module is designed to power APM,Pix32, a RC receiver and APM accessories (GPS, radio). It is not designed to power servos. Use your aircraft’s own ESC/BEC for that.
The GH terminal is also compatible with both Pix32,Pixhawk4,Pixhawk4 mini and Durandal.

Note: This PM02 Power Module uses analog data output and is not compatible to the Pixhawk 5X (Requires a digital PM like PM02D).

Features:

1. Light weight
2. Best for your DIY projects
3. Easy to Use

Packages Includes:

1 x Holybro Power Module PM02

F4 V3S Plus Flight Control OSD 2-6S Two-way 3A BEC 9V Pad Design for Betaflight FPV Racing Drone. The F4 V3S Plus Flight Control OSD is a controller board designed for racers. In contrast to a typical racer board, it has some additional features, such as an SD card and a faster CPU.

Specifications and Features:

1. Item name: F4 V3 PLUS Flight Controller
2. Firmware: Omnibus ~ f4
3. Board Dimensions: 36x36mm
4. Montagegaten: 30.5×30.5mm
5. STM32 F405 MCU
6. Dshot protocol
7. Slepen en Neerzetten OSD geconfigureerd via Betaflight
8. BMI270 6 axis SPI gyro & accelerometer
9. SBUS / PPM EN Spketrum DSMX poorten
10. MicroSD BlackBox
11. Baro (BMP280)
12. 5v3a 9V3A BEC
13. On-board video filters (alleen 5V naar VTX en camera)

Package Includes:

The Pixhawk 6C is the latest update to the successful family of Pixhawk flight controllers, based on the Pixhawk FMUv6C Open Standard and the Connector Standard. It comes with PX4 Autopilot pre-installed. Inside the Pixhawk 6C, you can find an STMicroelectronics based STM32H743, paired with sensor technology from Bosch® & InvenSense, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications.

The Pixhawk 6C’s H7 microcontroller contain the Arm Cortex-M7 core running up to 480 MHz, has 2MB flash memory and 1MB RAM. Thanks to the updated processing power, developers can be more productive and efficient with their development work, allowing for complex algorithms and models. The FMUv6C open standard includes high-performance, low-noise IMUs on board, designed to be cost effective while having IMU redundancy. A vibration isolation System to filter out high-frequency vibration and reduce noise to ensure accurate readings, allowing vehicles to reach better overall flight performances.

Features:

1. High performance H7 Processor with clock speed up to 480 MHz
2. New cost-effective design with low-profile form factor
3. Redundant inertial measurement unit (IMU) from Bosch & InvenSense
4. Newly designed integrated vibration isolation system to filter out high frequency vibration and reduce noise to ensure accurate readings
5. IMUs are temperature-controlled by onboard heating resistors, allowing optimum working temperature of IMUs

Packages Includes:

1 x  Holybro Pixhawk 6C PM02

Aocoda-RC F7DUAL F7 F722 BMI270 30.5MM flight controller 3-6S BEC Betaflight INAV is the latest flight controller from Aocoda-RC

Pin Diagrams:

Package Includes:

1 x Aocoda-RCF7DUAL F7 F722 BMI270 30.5MM flight controller

Feature:

1. Flight Control Built-in OSD / BEC
2. Micro-SD Back-box
3. Built-in Current Sensor
4. F4 Processor (F405)
5. On-Board Video Filter (only can supply 5V to VTX and Camera)

Specification:

1. SPI Gyro IC268G
2. On-Board OSD (controllered by Betaflight, FC over SPI bus)
3. MicroSD Blackbox
4. Baro (BMP280)( default is closed,need to open in configuration,if not know how to open,contact with us)
5. F4 Processor (F405)
6. 5v3a SBEC
7. Built-in Current Sensor
8. On-Board Video Filter (only can supply 5V to VTX and Camera)

Package include:

1 x F4 Pro V2 V3.5 v3s Flight Control Built-in OSD / BEC