This is a Radiolink Mini Pix Flight Controller. This Flight controller has PIXHAWK Vibration Damping by this it can reduce the Motor vibration. Also, it has two telemetry Stream by which it can Transmit both Data and images. Image Transmission Depends upon the rated voltage of image Transmission. This is useful if you’re flying in First Person View (FPV) mode or don’t want to use a laptop at the field to see your telemetry data in the Mission Planner.

Features:

1. It comes with a Cost-Effective Solution.
2. The shell of the Device to reduce interference of airflow during flying.
3. The small size reduces the weight of the whole machine and flies for a long time.

Package Includes:

1 x Radiolink Mini Pix Flight Controller

F4 V3S Plus Flight Control OSD 2-6S Two-way 3A BEC 9V Pad Design for Betaflight FPV Racing Drone. The F4 V3S Plus Flight Control OSD is a controller board designed for racers. In contrast to a typical racer board, it has some additional features, such as an SD card and a faster CPU.

Specifications and Features:

1. Item name: F4 V3 PLUS Flight Controller
2. Firmware: Omnibus ~ f4
3. Board Dimensions: 36x36mm
4. Montagegaten: 30.5×30.5mm
5. STM32 F405 MCU
6. Dshot protocol
7. Slepen en Neerzetten OSD geconfigureerd via Betaflight
8. BMI270 6 axis SPI gyro & accelerometer
9. SBUS / PPM EN Spketrum DSMX poorten
10. MicroSD BlackBox
11. Baro (BMP280)
12. 5v3a 9V3A BEC
13. On-board video filters (alleen 5V naar VTX en camera)

Package Includes:

The Power Management Board (PM Board) serves the purpose of a Power Module as well as a Power Distribution Board. In addition to providing regulated power to Pixhawk 4 and the ESCs, it sends information to the autopilot about battery’s voltage and current supplied to the flight controller and the motors.

Features:

1. Model: Pixhawk 4
2. Power: 1000mw
3. Frequency: 433 Mhz
4. Material: Composite Material
5. Weight: 62g
6. Board dimensions: 8 x 5 x 1mm

Packages Includes:

1 x Holybro Pixhawk 4 Power management board

The FMS Reflex system is programmed specifically for the aircraft it is connected to. No further programming is needed. The user only needs to connect their receiver to the gyro and set up the aircraft normally.

Reflex V2 can be reprogrammed easily with different model files via a simple software-allowing pilots to use the same flight control unit as they progress to different aircraft. Flying is simple when you have your very own “co-pilot”- the Reflex V2!

Features: 

1. 3 flight modes are available: Stabilized, Optimized or off. This is controlled with a 2 or 3 position switch on the transmitter. When assigned to a 2 position switch, the Reflex system switches between stabilized and optimized modes.
2. Stabilized Mode – Designed for beginners, Reflex will rapidly level the aircraft from any attitude when this mode is activated. Stabilized mode combines accelerometer and gyro data to determine how to level the aircraft when the control sticks are released- giving pilots absolute peace of mind.
3. OFF – Turns off all gyro functionality, the aircraft is flown completely manually when the gyro is off.
4. Optimized Mode – Utilizing advanced solid-state gyros, the Reflex system maintains aircraft attitude by counteracting inflight upsets- from gusts to crosswinds.

Specification:

1. Suitable For FMS 1.2M Ranger Plane.
2. Utilizes a high-speed 32-bit ARM processor onboard.
3. 3 axis gyro and 3 axes accelerometer.
4. 3 flight modes are available: Stabilized, Optimized, or off.
5. Automatically recognizes SBUS/PPM/PWM systems, compatible with all radio systems with 4 channels or above.
6. Easy operation.

Package Includes :

1 x FMS RC Airplane Gyro Reflex Flight Control System

This product is a combo kit of 1 Flight controller & 1 ESC which are highly efficient to work in drones, we brought this combo of flight controller & ESC  in a chipper price than the market price, This high-performance Flight controller is able to handle your Drone &  model plane controller with 95% accuracy.

ESC (Electronic Speed Controller) comes in the kit is compatible with flight controller they work together very efficiently.

The flight controller uses the data gathered by the sensors to calculate the desired speed for each of the four motors. The flight controller sends this desired speed to the Electronic Speed Controllers (ESC’s), which translates this desired speed into a signal that the motors can understand.

The MPU6000 is the most widely used IMU sensor, and it’s used in nearly all of the greatest flight controllers. The reason for this is that it has a high vibration tolerance and can sample the gyro at 8kHz over an SPI interface.

1. Note: Product can vary from images in terms of Color and Design & Damper shown in image is not included in pack

Features:

1. This is a combo kit of Flight controller & ESC
2. High-performance & efficient flight controller & ESC
3. Lightweight, Easy to connect
4. Compact in size
5. The flight controller comes with an ARM processor
6. ESC is built to give the best performance

Packages Includes:

1 x F405 V1.0 Flight Controller

1 x 45A 2-6S 4 in 1 ESC Flytower (mpu6000)

1 x Screw Pack

The Holybro Kakute H7 v2 Flight Controller is full of features including integrated Bluetooth, HD camera plug, dual plug-and-play 4in1 ESC ports, 9V VTX ON/OFF Pit Switch, barometer, OSD, 6x UARTs, 128MB Flash for Logging, 5V and 9V BEC, and bigger soldering pad with easy layout and much more.

The Kakute H7 v2 builds upon the best features of its F7 predecessor and further improves on hardware components and layout. With the additional integrated Bluetooth chip onboard, you can perform configuration and tuning wirelessly on your phone with the SpeedyBee Android & IOS App. The Kakute H7 is DJI HD ready. It has an easy plug-and-play port with an on-board 9V regulator designed to power your HD video transmitter such as the DJI/Caddx FPV Air Unit & Caddx Vista while supporting analog system.

It features an onboard “VTX ON/OFF Pit Switch” that allows you to completely power off the video transmitter using a switch on your RC transmitter. Great if you are working on your drone, waiting for the GPS to get a fix, getting ready for a race while preventing it from overheating or interfering with others flying. It has 6x dedicated UART ports with built-in inversion for peripherals (UART2 is used for Bluetooth telemetry), a 128 MB Flash for logging, Dual plug-and-play 4in1 ESC connectors, allowing easy plug-and-play support for x8 & Octocopter configuration and keeping it simple and clean. The integrated BetaFlight OSD makes it easy to display important information on your FPV display like battery voltage, flight time, warnings, RSSI, smart audio features and more. It is also ready for autonomous flight with the on-board barometer. There are LED & buzzer pad, I2C pad (SDA & SCL) for external GPS/Magnetometers.

Note:

1. The Bluetooth onboard is set to automatically turn off when the flight controller is unlocked (arm) and turn on automatically when the flight controller is locked (disarm).
2. Warning: Do not enable this pit switch if you are using DJI FPV Remote Controller

Features:

1. SpeedyBee IOS & Android App Compatible
2. Light weight
3. You can adjust Beta Flight OSD, PIDs, VTX channel/power level, and other parameters directly by using the transmitter and goggles
4. New high-performance, highly sensitive IMU – ICM20689 with 6-axis gyro and accelerometer
5. The IMU, which is mounted on a vibration-isolation foam, measures more precisely
6. 120A maximum continuous current, 7 – 42V input voltage, and automatic voltage monitoring
7. Supports BetaFlight and Clean Flight, as well as BLHeli pass-through for ESC upgrade and configuration

Specifications:

1. MCU: STM32H743 32-bit processor running at 480 MHz
2. IMU: BMI270
3. Barometer: BMP280
4. OSD : AT7456E
5. Onboard Bluetooth chip: ESP32-C3
6. VTX ON/OFF Pit Switch – Switch can be enable using USER1 in Beta flight Mode tab.
7. 6 x UARTs (1,2,3,4,6,7; UART2 is used for Bluetooth telemetry)
8. 9 x PWM Outputs (8 Motor Output, 1 LED)
9. 2 x JST-SH1.0_8pin port (4in1 ESCs, x8/Octocopter compatible)
10. 1 x JST-GH1.25_6pin port (For HD System like Caddx Vista & Air Unit)
11. Battery input voltage: 7V to 42V
12. BEC 5V 2A Cont.
13. BEC 9V 1.5A Cont.
14. Mounting – 30.5 x 30.5mm/Φ4mm hole with Φ3mm Grommets
15. Dimension – 35 x 35mm
16. Weight – 8g

Packages Includes:

1 x Holybro Kakute H7 V2 Flight Controller