- 35% Off Industrial and Drone Parts.
- Free carbon neutral shipping on India orders ₹ 2000+.
End of Time:
:
:
:
0
0 items
₹0.00
No products in the cart.
- Input voltage: DC12-24V
- Amp Chip: TPA3116D2
- Output impedance:4~8 ohm Speaker
- Current: ≥3A
- Output power: 80W*2
- Adopt a TPA3116D2 high-performance power amplifier chip.
- With total volume, subwoofer volume, and stereo volume control knobs.
Add to Wishlist
Add to Wishlist
- Input: 5V(DC)
- Operating current (without signal output state): less than 15 mA
- Operating current (with signal output state): less than 40 mA
- Chip: KT403A
- Chip LDO output voltage: 3.3 V
- Chip output current: 100 mA(at Max.)
Add to Wishlist
Add to Wishlist
- Working Voltage: 3.⅗V
- Working Current (@5V, 25℃)
- Standby: 25-30mA
- Recording: 29-35mA
- Playing: 110-150mA
- Working Current (@3.3V, 25℃)
- Standby: 23-25mA
- Recording: 25-30mA
- Playing: 70-150mA
- Working Temperature: 0~85℃
- Size: 40x20mm
- Weight: 31.5g
Add to Wishlist
Add to Wishlist
- Brand: Seeed Studio
- Supply voltage: 3.3V +-0.2V
- Sound Pressure Level: 140 dB SPL
- Sensitivity: -26(dB, dBFS @1kHz 1Pa)
- 6 MEMS microphones: MSM261S4030H0
- Supply current: >750mA(Full brightness)
- Range of working temperature: -30 ~ 85C
Add to Wishlist
Add to Wishlist
- Input Voltage: 3.3V~5.5V
- Operating Current: 5mA (25mA in VOC Measurement)
- Communication Interface: I2C(Support 3.3V/5V) or SPI(other non-I2C ports only support 3.3V)
- Default I2C Address: 0x76
- Temperature Measurement Range: -40℃~+85℃
- Temperature Measurement Precision: ±1.0℃(0~65℃)
- Humidity Measurement Range: 0-100%r.H.
- Humidity Measurement Precision: ±3%r.H.(20-80% r.H.,25℃)
Add to Wishlist
Add to Wishlist
- Signal Type: Analog signal
- Power Supply: 3.3V/5V
- Directivity: All-round
- Sensitivity: -42dB
- S/N Ratio: 59dBA
- Frequency Range: 100Hz~8KHz
Add to Wishlist
Add to Wishlist
- Work voltage:DC 12V-28V
- IC:TPA3118D2
- Power interface:DC 5.5*2.1mm socket
- Audio channel:2CH
- Output power:45W*2
- Input current:>3A
- Output impedance:4ohm-8ohm
Add to Wishlist
Add to Wishlist
- Module Type: TDA8932 35W
- Operating Voltage: Single DC10 ~ 30V
- Recommended Voltage: 24V
- Current: Above 2A Switching Power Supply
- Output Power: 35W x 1
- Speaker Impedance: 4-8 ohm, 8 ohm best
- Circuit configuration: Mono BTL Output
Add to Wishlist
Add to Wishlist
- Item Type: Amplifier Board
- Model: HF69B
- Supply Voltage: 5VDC or 3.7V lithium battery
- Applicable Speaker Impedance: 4 ohms, 6 ohms, 8 ohms
- Charging Interface: When using a lithium battery, the charging interface can be charged with a 5 volt power supply or a mobile phone charger to charge a single lithium battery.
Add to Wishlist
Add to Wishlist
- MP3 file format:
- support all bit rate 11172-3 and ISO13813-3 layer3 audio decoding
- Sample rate support (KHZ): 8/11.025/12/16/22.05/24/32/44.1/48
- support Normal, Jazz, Classical, Pop, Rock and other sound effects
- UART interface: standard serial port, TTL level, baud rate can be set
- Input voltage: 3.2V-5V (best 4.2V);
- Rated current: 20ma
Add to Wishlist
Add to Wishlist
- Working Voltage: 3.3V DC.
- Working Current: 35mA.
- Output Signal: I2C, UART.
- Working Temperature: -20~70℃.
- Size: 30mm x 20.5mm/1.18 x 0.81″
Add to Wishlist
Add to Wishlist
- 40PIN GPIO, Compatible with all the Raspberry Pi Boards.
- Onboard TSL25911FN digital ambient light sensor, for measuring IR and visible light
- Onboard BME280 sensor, for measuring temperature, humidity, and air pressure
- Onboard ICM20948 motion sensor, accelerometer, gyroscope, and magnetometer
- Onboard LTR390-UV-1 sensor, for measuring UV rays
- Onboard SGP40 sensor, for detecting ambient VOC
Add to Wishlist
Add to Wishlist
- Operating voltage: 3.3V/5V
- Communication interface: I2C/SPI
- Dimension: 27mm x 20mm
- Mounting hole size: 2.0mm
Add to Wishlist
Add to Wishlist
- Gravity interface, no need to solder, plug and play
- Switchable I2C and UART, two output modes
- Highly integrated module can test a variety of data at the same time
- Reasonable layout and high precision
Add to Wishlist
Add to Wishlist
- Output Power: 3.2W at 4Ω, 10% THD, 1.8W at 8Ω, 10% THD, with 5V supply
- PSRR: 77 dB typ @ 1KHz
- I2S sample rates from 8kHz to 96kHz
- No MCLK required
Add to Wishlist
Add to Wishlist
- PM, NOx, VOC, RH & T Sensor Platform
- Fast and Easy integration
- One Driver for up to 8 data signal
- Superior Sensing accuracy and lifetime
- Fully calibrated digital output
Add to Wishlist
Add to Wishlist
Basic Components – Resistors | Capacitors | LEDs | Inductor | Varistor | Breadboard | Oscillator
Important links
Need Help?
+91 7231900002 (whatsapp)
Monday – Friday: 9:00-20:00
Saturady: 11:00 – 15:00
Customer Service
- -5% for all order in this week Shop now
- Free delivery for all orders over ₹ 2000