BQ2057CSN – 4.1V Linear 1-cell Li-ion Charge Controller AutoCompTM IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x BQ2057CSN – 4.1V Linear 1-cell Li-ion Charge Controller AutoCompTM IC SMD-8 Package

TNY276PN – POWER INTEGRATI

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x TNY276PN – POWER INTEGRATI

TNY266PN – POWER INTEGRATI

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x TNY266PN – POWER INTEGRATI

The DRV835x family of devices are highly-integrated gate drivers for three-phase brushless DC (BLDC) motor applications. These applications include field- oriented control (FOC), sinusoidal current control, and trapezoidal current control of BLDC motors. The device variants provide optional integrated current shunt amplifiers to support different motor control schemes and a buck regulator to power the gate driver or external controller. The DRV835x uses smart gate drive (SGD) architecture to decrease the number of external components that are typically necessary for MOSFET slew rate control and protection circuits. The SGD architecture also optimizes dead time to prevent shoot-through conditions, provides flexibility in decreasing electromagnetic interference (EMI) by MOSFET slew rate control, and protects against gate short circuit conditions through VGS monitors. A strong gate pulldown circuit helps prevent unwanted dV/dt parasitic gate turn on events Various PWM control modes (6x, 3x, 1x, and independent) are supported for simple interfacing to the external controller. These modes can decrease the number of outputs required of the controller for the motor driver PWM control signals. This family of devices also includes 1x PWM mode for simple sensored trapezoidal control of a BLDC motor by using an internal block commutation table.

Applications:

1. 3-phase brushless-DC (BLDC) motor modules
2. Fans, blowers, and pumps
3. E-Bikes, E-scooters, and E-mobility
4. Power and garden tools, lawn mowers
5. Drones, robotics, and RC toys
6. Factory automation and textile machines

Specifications:

1. Operating Voltage: 6V ~ 95V
2. Current: 25mA
3. Technology: Power MOSFET
4. Interface: SPI
5. Mounting type: SMD
6. Output conflagration: Half Bridge
7. Operating temperature: -40°C ~ 125°C (TA)

Note: For more info refer to datasheet

Packages Includes:

1 x DRV8353RSRGZR IC

The MAX186 are 12-bit data-acquisition systems that combine an 8-channel multiplexer, high bandwidth track/hold, and serial interface together with high conversion speed and ultra-low power consumption. The devices operate with a single +5V supply or dual ±5V supply. The analog inputs are software configurable for unipolar/bipolar and single-ended/differential operation. The 4-wire serial interface directly connects to SPI, QSPI™, and MICROWIRE® devices without external logic. A serial strobe output allows direct connection to TMS320 family digital signal processors.

The MAX186 uses either the internal clock or an external serial-interface clock to perform successive approximation A/D conversions. The serial interface can operate beyond 4MHz when the internal clock is used. The MAX186 has an internal 4.096V reference. The MAX186 provides a hard-wired SHDN pin and two software-selectable power-down modes. Accessing the serial interface automatically powers up the devices, and the quick turn-on time allows the MAX186 to be shut down between every conversion. Using this technique of powering down between conversions, supply current can be cut to under 10µA at reduced sampling rates. The MAX186 is available in 20-pin PDIP and SO packages, and in a shrink small-outline package (SSOP), that occupies 30% less area than an 8-pin PDIP.

Application:

1. Portable Data Logging
2. Data-Acquisition
3. High-Accuracy Process Control
4. Automatic Testing
5. Robotics
6. Battery-Powered Instruments
7. Medical Instruments

Features:

1. Internal Track/Hold, 133kHz Sampling Rate
2.  SPI-/QSPI-/MICROWIRE-/TMS320-Compatible 4-Wire Serial Interface
3.  Software-Configurable Unipolar or Bipolar Inputs
4.  20-Pin PDIP, SO, SSOP Packages
5.  Evaluation Kit Available

Package Includes:

1 x MAX186CCPP+ Low Power 8-Channel Serial 12-Bit ADC Maxim DIP-20 Package

MAX13088EESA+ – MAXIM INTEGRATE

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x MAX13088EESA+ – MAXIM INTEGRATE