BQ24030RHLR – 6V Dual Input Li-Ion Battery Charger Dynamic Power-Path Management IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x BQ24030RHLR – 6V Dual Input Li-Ion Battery Charger Dynamic Power-Path Management IC VQFN-20 Package

TOP245YN – POWER INTEGRATI

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x TOP245YN – POWER INTEGRATI

Extended power range for higher power applications, No heat sink required up to 34 W using P/G packages, Features eliminate or reduce cost of external components, Fully integrated soft-start for minimum stress/overshoot, Externally programmable accurate current limit, Wider duty cycle for more power, smaller input capacitor, Separate line sense and current limit pins on Y/R/F.

Note for more details refer to datasheet.

1. Series: TOPSwitch-GX
2. Package: Tube
3. Standard Package: 50
4. Product Status: Not For New Designs
5. Output Isolation: Isolated
6. Internal Switch(s): Yes
7. Voltage – Breakdown: 700V
8. Topology: Flyback
9. Duty Cycle: 66.5%
10. Frequency – Switching: 66kHz ~ 132kHz
11. Power (Watts): 45 W
12. Fault Protection: Current Limiting | Over Temperature | Over Voltage
13. Control Features: Frequency Control
14. Operating Temperature: -40°C ~ 150°C (TJ)
15. Package / Case: TO-220-7 Formed Leads | 6 Leads
16. Supplier Device Package: TO-220-7C
17. Mounting Type: Through Hole
18. Base Product Number: TOP243

Packages Includes:

1 x TOP243YN – POWER INTEGRATI

The DRV835x family of devices are highly-integrated gate drivers for three-phase brushless DC (BLDC) motor applications. These applications include field- oriented control (FOC), sinusoidal current control, and trapezoidal current control of BLDC motors. The device variants provide optional integrated current shunt amplifiers to support different motor control schemes and a buck regulator to power the gate driver or external controller. The DRV835x uses smart gate drive (SGD) architecture to decrease the number of external components that are typically necessary for MOSFET slew rate control and protection circuits. The SGD architecture also optimizes dead time to prevent shoot-through conditions, provides flexibility in decreasing electromagnetic interference (EMI) by MOSFET slew rate control, and protects against gate short circuit conditions through VGS monitors. A strong gate pulldown circuit helps prevent unwanted dV/dt parasitic gate turn on events Various PWM control modes (6x, 3x, 1x, and independent) are supported for simple interfacing to the external controller. These modes can decrease the number of outputs required of the controller for the motor driver PWM control signals. This family of devices also includes 1x PWM mode for simple sensored trapezoidal control of a BLDC motor by using an internal block commutation table.

Applications:

1. 3-phase brushless-DC (BLDC) motor modules
2. Fans, blowers, and pumps
3. E-Bikes, E-scooters, and E-mobility
4. Power and garden tools, lawn mowers
5. Drones, robotics, and RC toys
6. Factory automation and textile machines

Specifications:

1. Operating Voltage: 6V ~ 95V
2. Current: 25mA
3. Technology: Power MOSFET
4. Interface: SPI
5. Mounting type: SMD
6. Output conflagration: Half Bridge

Note: For more info refer to datasheet

Packages Includes:

1 x DRV8353RHRGZT IC

The NCP1117 series are low dropout positive voltage regulators that are capable of providing an output current that is in excess of 1.0 A with a maximum dropout voltage of 1.2 V at 800 mA over temperature. This series contains nine fixed output voltages of 1.5 V, 1.8 V, 1.9 V, 2.0 V, 2.5 V, 2.85 V, 3.3 V, 5.0 V, and 12 V that have no minimum load requirement to maintain regulation. Also included is an adjustable output version that can be programmed from 1.25 V to 18.8 V with two external resistors. On-chip trimming adjusts the reference/output voltage to within ±1.0% accuracy. Internal protection features consist of output current limiting, safe operating area compensation, and thermal shutdown. The NCP1117 series can operate with up to 20 V input. Devices are available in SOT−223 and DPAK packages.

Application:

1. Consumer and Industrial Equipment Point of Regulation
2. Active SCSI Termination for 2.85 V Version
3.  Switching Power Supply Post Regulation
4. Hard Drive Controllers
5.  Battery Chargers

Features:

1.  Adjustable Output Voltage Option
2.  No Minimum Load Requirement for Fixed Voltage Output Devices
3.  Reference/Output Voltage Trimmed to ±1.0%
4.  Current Limit, Safe Operating, and Thermal Shutdown Protection
5.  The operation to 20 V Input
6.  These are Pb-Free Devices

Specifications:

1. Mounting Style: SMD/SMT
2. Package/Case: SOT-223-3
3. Output Voltage: 3.3 V
4. Output Current: 1 A
5. Number of Outputs: 1 Output
6. Polarity: Positive
7. Quiescent Current: 10 mA
8. Input Voltage MAX: 20 V
9. Input Voltage MIN: 4.75 V
10. Output Type: Fixed
11. Minimum Operating Temperature: 0 C
12. Maximum Operating Temperature: + 125 C
13. Dropout Voltage: 950 mV

Package Includes:

1 x NCP1117ST33T3G – 3.3V 1A Fixed/Adjustable Positive LDO Regulator 4-Pin SOT-223 (ON semiconductor)

The MAX186 are 12-bit data-acquisition systems that combine an 8-channel multiplexer, high bandwidth track/hold, and serial interface together with high conversion speed and ultra-low power consumption. The devices operate with a single +5V supply or dual ±5V supply. The analog inputs are software configurable for unipolar/bipolar and single-ended/differential operation. The 4-wire serial interface directly connects to SPI, QSPI™, and MICROWIRE® devices without external logic. A serial strobe output allows direct connection to TMS320 family digital signal processors.

The MAX186 uses either the internal clock or an external serial-interface clock to perform successive approximation A/D conversions. The serial interface can operate beyond 4MHz when the internal clock is used. The MAX186 has an internal 4.096V reference. The MAX186 provides a hard-wired SHDN pin and two software-selectable power-down modes. Accessing the serial interface automatically powers up the devices, and the quick turn-on time allows the MAX186 to be shut down between every conversion. Using this technique of powering down between conversions, supply current can be cut to under 10µA at reduced sampling rates. The MAX186 is available in 20-pin PDIP and SO packages, and in a shrink small-outline package (SSOP), that occupies 30% less area than an 8-pin PDIP.

Application:

1. Portable Data Logging
2. Data-Acquisition
3. High-Accuracy Process Control
4. Automatic Testing
5. Robotics
6. Battery-Powered Instruments
7. Medical Instruments

Features:

1. Internal Track/Hold, 133kHz Sampling Rate
2.  SPI-/QSPI-/MICROWIRE-/TMS320-Compatible 4-Wire Serial Interface
3.  Software-Configurable Unipolar or Bipolar Inputs
4.  20-Pin PDIP, SO, SSOP Packages
5.  Evaluation Kit Available

Package Includes:

1 x MAX186CCPP+ Low Power 8-Channel Serial 12-Bit ADC Maxim DIP-20 Package