- 35% Off Industrial and Drone Parts.
- Free carbon neutral shipping on India orders ₹ 2000+.
End of Time:
:
:
:
0
0 items
₹0.00
No products in the cart.
- Main chip: ESP32-WROVER-B, SIM7000G
- Flash Memory:4M Flash / 8M PSRAM
- Interface: USB, SD Card, Solar Input interface
- Car Clock:40MHz
- Button: Reset, Power switch
- SIM Card Size: Nano SIM Card
- Antenna: SIM Antenna,GPS Antenna
- Operating Temperature Range:-40-85 degrees
Add to Wishlist
Add to Wishlist
- Main chip:ESP32 WROVER-B
- Interface: USB, SD Card, Solar Input interface
- Car Clock:40MHz
- Button: Reset, Power switch
- Antenna: SIM Antenna,GPS Antenna
- Operating Temperature Range:-40-85 degrees
Add to Wishlist
Add to Wishlist
- Very low power logging is supported
- Built-in MCP73831 single cell LiPo charger
- Current consumption
- ~20mA (Run)
- ~80µA (Sleep)
- ~18µA (Deep Sleep – regulator shut down)
- LEDs
- Power
- LiPo charge indicator
- Serial Tx and Rx
- Status
Add to Wishlist
Add to Wishlist
- Power amplifier chip NS4168
- I2S serial digital audio input interface
- Support a wide range of sampling rates: 8kHz~96kHz
- Automatic sampling rate detection, adaptive function
Add to Wishlist
Add to Wishlist
- Support type:16G FAT/FAT32 MicroSD
- Compatible with ATOM Matrix/ ATOM Lite
- Up to 16G TF card
- FAT/FAT32 format
Add to Wishlist
Add to Wishlist
- ESP32 Standard wireless functions WiFi, Bluetooth
- Internal 4M Flash
- Low Power Display
- 180-degree viewing angle
Add to Wishlist
Add to Wishlist
- Input Voltage:3-5.5 V
- Flash Memory:8 MB
- Powered by RP2040
- User controllable RGB LED
- USB-C connector for power, programming, and data transfer
Add to Wishlist
Add to Wishlist
- Operating voltage: 3.3V / 5V
- Interface: 3-wire SPI, 4-wire SPI
- Outline dimension: 42mm × 27mm
- Display size: 21.76mm × 14mm
- Dot pitch: 0.175 × 0.17
- Resolution: 128 × 80
- Display color: black, white
- No backlight keeps displaying last content for a long time even when power down
- Ultra-low power consumption, basically power is only required for refreshing
- SPI control interface, for working with host boards such as Raspberry Pi/Jetson Nano/Arduino.
Add to Wishlist
Add to Wishlist
- Operating voltage: 3.3V/5V
- Interface: 3-wire SPI, 4-wire SPI
- Dot pitch: 0.181 × 0.181
- No backlight keeps displaying last content for a long time even when power down
- Ultra-low power consumption, basically power is only required for refreshing
- SPI interface, for connecting with controller boards like Raspberry Pi/Nucleo, etc.
Add to Wishlist
Add to Wishlist
- Operating voltage: 3.3V/5V
- Display color: ACep 7-Color
- Interface: 3-wire SPI, 4-wire SPI
- Crey scale: 2
- Display size: 86.40 × 54.00mm
- Dot pitch: 0.135 × 0.135mm
- Resolution: 640 × 400 pixels
- Advanced Color ePaper (ACeP) technology, supports a 7-Color display
- No backlight keeps displaying last content for a long time even when power down
- Ultra-low power consumption, basically power is only required for refreshing
- Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
Add to Wishlist
Add to Wishlist
- Power: NFC-powered
- Resolution: 400×300
- Dot pitch: 0x212x 0x212
- Refresh time: 4s
- No backlight required, e-Paper keep displaying the last content for a long time without power
- No power adapter required
Add to Wishlist
Add to Wishlist
- Input Voltage (V):3.3V@600mA
- Processor: Kinetis KL26 Arm® Cortex®-M0+ MCU
- Maximum Clock Frequency (MHz):48
- Flash Memory:128kB
- SRAM:16kB
- Dimension:95x38x10 mm
- Weight:21 gm
Add to Wishlist
Add to Wishlist
- Working voltage: 3.3V
- Input voltage: 3.3V~5V
- Support electric current of low power consumption: 10 μA
- Support maximum discharge current: 600mA
- Quick Response(the top frequency is 400KHz)
- Cost-effective
- Small size, convenient to install
Add to Wishlist
Add to Wishlist
- WiFi+Bluetooth 4.0 Dual-mode Module
- GDI Display Port, easy to connect
- Operating Voltage: 3.3V
- Input Voltage: 3.3V~5.5V
- Support Low-Power: 10uA
- ESP32 Dual-core low power main controller, 10uA power consumption
Add to Wishlist
Add to Wishlist
- Operating Current: 3.3V
- Operating Frequency: 433MHz
- Modulation Type: LoRaTM
- Output Power: ≤20dBm
- Receiving Sensitivity: -139dBm
Add to Wishlist
Add to Wishlist
- 24 I/O channels with input protection circuitry
- Adjustable target voltage: 1.2 V to 3.3 V
- Supported target interfaces (as of firmware v1.1): JTAG/IEEE 1149.1, UART/asynchronous serial
- USB interface for direct connection to the host computer
Add to Wishlist
Add to Wishlist
Basic Components – Resistors | Capacitors | LEDs | Inductor | Varistor | Breadboard | Oscillator
Important links
Need Help?
+91 7231900002 (whatsapp)
Monday – Friday: 9:00-20:00
Saturady: 11:00 – 15:00
Customer Service
- -5% for all order in this week Shop now
- Free delivery for all orders over ₹ 2000