4 x 18650 Lithium Battery Shield V8 V9 for Arduino ESP32 ESP8266

SKU: 1031026
Out of stock

879.00

Add to Wishlist
Add to Wishlist
  1. Working Temperature: -20 °C~70 °C
  2. Output Port: USB or Expansion port
  3. Output Parameters: 5V/3A or 3V/1A
  4. Conversion Efficiency: up to 95% 
Out of stock

Did you like this product? Add to favorites now and follow the product.

Add to Wishlist
Add to Wishlist

Description

This is a 4x 18650 Lithium Battery Shield V8 V9 Mobile Power Expansion Board Module 5V/3A 3V/1A Micro USB for Arduino ESP32 ESP8266. This mobile power supply has a built-in lithium battery protection IC, which has overcurrent, overvoltage, Under voltage protection, and the module is a portable mobile power supply that supports 3V/1A and 5V/3A two voltage outputs with an onboard voltage switching button

Installation of the battery must be determined positive and negative, the board has been clearly marked positive and negative Or Installation errors will burn out the module. The battery voltage works normally from 3.2V to 4.2V. 5V voltage output rated current is 3A, maximum support 3.6A current, the output of current depends on the quality of the 18650 battery.

Note: This product comes from different brands. We will ship it randomly according to availability.


Features:

  1. Supports 3V 1A voltage outputs.
  2. Supports 5V 3A voltage outputs.
  3. Micro USB charging current is 600mA-800mA.
  4. Supports up to two 18650 batteries. It is recommended to use two 18650 batteries, which can be longer.

Package Includes:

1 x 4 x 18650 Lithium Battery Shield V8 V9 for Arduino ESP32 ESP8266

Additional information

Output Voltage(V)

3V/5V

Output Port Type

USB or Expansion

Input Port

MicroUSB

Conversion Efficiency(%)

95 %

Length (mm)

100

Width (mm)

90

Height (mm)

20

Weight (gm)

71

Quick Comparison

Settings4 x 18650 Lithium Battery Shield V8 V9 for Arduino ESP32 ESP8266 removeAdafruit PowerBoost 1000 Charger – Rechargeable 5V Lipo USB Boost @ 1A – 1000C removeSKYRC BD250 2-8S LiPo/LiFe Battery Discharger / Analyzer removeSKYRC PC1260 Dual Channel 12S LiPo Battery Charger removeSKYRC PC520 520W 20A Dual Channel 6S LiPo Charger remove18650 5V 2.4A Lithium, Battery Digital Display, Charging Module Dual, USB Output Band, Display Booster, Mmodule remove
Name4 x 18650 Lithium Battery Shield V8 V9 for Arduino ESP32 ESP8266 removeAdafruit PowerBoost 1000 Charger – Rechargeable 5V Lipo USB Boost @ 1A – 1000C removeSKYRC BD250 2-8S LiPo/LiFe Battery Discharger / Analyzer removeSKYRC PC1260 Dual Channel 12S LiPo Battery Charger removeSKYRC PC520 520W 20A Dual Channel 6S LiPo Charger remove18650 5V 2.4A Lithium, Battery Digital Display, Charging Module Dual, USB Output Band, Display Booster, Mmodule remove
Image
SKU1031026117844788626188626412200161121220
Rating
Price879.002,220.006,049.0028,999.0010,999.00265.00
Stock
Out of stock
Out of stock
Out of stock
In Stock
In Stock
Out of stock
AvailabilityOut of stockOut of stockOut of stockIn StockIn StockOut of stock
Add to cart

Read more

Read more

Read more

Add to cart

Add to cart

Read more

Description
  1. Working Temperature: -20 °C~70 °C
  2. Output Port: USB or Expansion port
  3. Output Parameters: 5V/3A or 3V/1A
  4. Conversion Efficiency: up to 95% 
  1. 2A internal switch (~2.5A peak limiting)
  2. 1000mA+ from a 3.7V LiPoly/LiIon battery.
  3. Low battery indicator LED lights
  4. PCB Dimensions: 19mm x 32mm x 5mm / 0.7″ x 1.3″ x 0.2″
  5. Weight: 2.5g
  1. Displays real-time battery voltage, discharged capacity, and discharge current.
  2. Test battery capacity that helps select batteries with the desired capacity.
  3. Saves time when users wish to store their large-capacity batteries.
  4. Breakthrough cooling system.
  5. Simple and intuitive operation.
  6. Test virtually any type, size, and chemistry battery.
  7. Easy-to-use PC software for data analysis.
  1. Supports charging 2 packs of 12s LiPo batteries simultaneously
  2. Supports high voltage LiPo(LiHV) battery
  3. 3 Working modes: balance charge, storage & charge.
  4. Adjustable charging current
  5. 2×16 LCD screen
  6. Real-time charging/discharging status display
  7. Battery status meter
  1. Supports 6s LiPo battery Adjustable charge current from 1.0 to 20.0A
  2. The charger can store the charge current of the last charge program
  3. LED digits on indicate charge/discharge status
  4. Two working modes: balance charge mode and storage mode

 

  1. Input:5V 2.1A
  2. Output:5V/1A or 5V/2.4A(Quick Charge )
  3. Size:66*18*16mm
  4. Protect Function: Overcharging; Overdischarging and overload protection
Content

This is a 4x 18650 Lithium Battery Shield V8 V9 Mobile Power Expansion Board Module 5V/3A 3V/1A Micro USB for Arduino ESP32 ESP8266. This mobile power supply has a built-in lithium battery protection IC, which has overcurrent, overvoltage, Under voltage protection, and the module is a portable mobile power supply that supports 3V/1A and 5V/3A two voltage outputs with an onboard voltage switching button

Installation of the battery must be determined positive and negative, the board has been clearly marked positive and negative Or Installation errors will burn out the module. The battery voltage works normally from 3.2V to 4.2V. 5V voltage output rated current is 3A, maximum support 3.6A current, the output of current depends on the quality of the 18650 battery.

Note: This product comes from different brands. We will ship it randomly according to availability.


Features:

  1. Supports 3V 1A voltage outputs.
  2. Supports 5V 3A voltage outputs.
  3. Micro USB charging current is 600mA-800mA.
  4. Supports up to two 18650 batteries. It is recommended to use two 18650 batteries, which can be longer.

Package Includes:

1 x 4 x 18650 Lithium Battery Shield V8 V9 for Arduino ESP32 ESP8266

PowerBoost 1000C is the perfect power supply for your portable project! With a built-in load-sharing battery charger circuit, you’ll be able to keep your power-hungry project running even while recharging the battery! This little DC/DC boost converter module can be powered by any 3.7V LiIon/LiPoly battery, and convert the battery output to 5.2V DC for running your 5V projects.

Like our popular 5V 1A USB wall adapter, we tweaked the output to be 5.2V instead of a straight-up 5.0V so that there’s a little bit of ‘headroom’ for long cables, high draw, the addition of a diode on the output if you wish, etc. The 5.2V is safe for all 5V-powered electronics like Arduino, Raspberry Pi, or Beagle Bone while preventing icky brown-outs during high current draw because of USB cable resistance.

The PowerBoost 1000C has at the heart a TPS61090 boost converter from TI. This boost converter chip has some really nice extras such as low battery detection, 2A internal switch, synchronous conversion, excellent efficiency, and 700KHz high-frequency operation. Check out these specs!

To make this even more useful, we stuck a smart load-sharing Lipoly charger on the other side. The charger circuitry is powered from a micro USB jack and will recharge any 3.7V/4.2V LiIon or LiPoly battery at a 1000mA max rate. There are two LEDs for monitoring the charge rate, a yellow one tells you it’s working, a green one lights up when it’s done.

Since the built-in battery charger has load-sharing, it will automatically switch over to the USB power when available, instead of continuously charging/draining the battery. This is more efficient and lets you charge and boost at the same time without any interruption on the output so it’s fine for use as a “UPS” (uninterruptable power supply). Please note that this board is designed to be used only with a LiPoly attached, it won’t work without a battery.


Features: 

  1. Synchronous operation means you can disconnect the output completely by connecting the ENable pin to the ground. This will completely turn off the output
  2. 2A internal switch (~2.5A peak limiting) means you can get 1000mA+ from a 3.7V LiPoly/LiIon battery. Just make sure your battery can handle it!
  3. Low battery indicator LED lights up red when the voltage dips below 3.2V, optimized for LiPo/LiIon battery usage
  4. Onboard 1000mA charge-rate ‘iOS’ data resistors. Solder in the USB connector and you can plug in any iPad, iPhone or iPod for a 1000mA charge rate.
  5. Full breakout for battery in, control pins and power out
  6. 90%+ operating efficiency in most cases (see datasheet for efficiency graphs), and low quiescent current: 5mA when enabled and power LED is on, 20uA when disabled (power and low batt LED are off)

Specification:

  1. PCB Dimensions: 19mm x 32mm x 5mm / 0.7″ x 1.3″ x 0.2″
  2. Weight: 2.5g

Package Includes:

1 x Adafruit PowerBoost 1000 Charger

Powerful, Robust, Simple

The SkyRC BD250 is a powerful discharging device that allows the user to discharge a battery at up to 35 amps or 250 watts and also measures and compares the performance of batteries. BD250 allows for the precise measurement of battery capacity and takes the guesswork out of choosing the best battery for your application.

The BD250 is much more than a simple battery discharger or a battery load tester. It will test virtually any type or size of the battery, any chemistry or number of cells, up to 35 volts.

It is small with a high-performance cooling system and uses MOS fets from the well-known brand IXYS, to make sure it can discharge at 250 watts continuously.

Big Breakthrough Fan System

A single, larger fan pushes air downward through an extruded aluminum heat sink. As air passes vertically through the heat sink, it absorbs heat and carries it out. This makes the BD250 discharge rate at 250 watts continuous possible.


Features:

  1. It displays real-time battery voltage, discharged capacity, and discharge current.
  2. It can test battery capacity that helps select batteries with desired capacity.
  3. It saves time when the user wishes to store their large-capacity batteries.
  4. It helps activate the best performance of your batteries during racing competitions.

Package Includes:

1 x SKYRC BD250 2-8S LiPo/LiFe Battery Discharger / Analyzer

1 x XT60 Discharge Cable

1 x Replacement Fuse

SkyRC PC1260 is a dual-channel 12S LiPo charger for industrial application drones. It is reliable, safe and easy to operate while with comprehensive functionality, like battery voltage meter, internal resistance meter, LiHV charging mode, also time-saving synchronization mode.

This charger is capable of balance charging 2 packs of 12 cell batteries simultaneously. It is specifically designed for the big battery pack.  The charger is equipped with a master-slave control mode, which allows you to synchronize more than one charger when charging the same batteries. It uses an advanced 32bits high-speed CPU from STMicroelectronics which improves its processing capability by 20 times.


Features:

  1. Sophisticated industrial and mechanical design
  2. Advanced 32bits high-speed CPU from STMicroelectronics, processing capability improves 20 times.
  3. High-Frequency Capacitor: Using a high spec large capacitor, ensures the charger can work properly for a longer period of time.
  4. Active PFC: Active PFC uses circuitry to correct the amount of power drawn to obtain the best ratio of power factor, achieving high efficiency, 93%. Which makes the product more stable and reduces the interferences to the power grid.
  5. Switched-mode Power Supply: Accepts power from mains supplies throughout the world.
  6. Conformal Coating: The conformal coating helps electronics withstanding harsh environments, and protects them against moisture, dust, chemicals, corrosive attack and temperature extremes etc.It also ensures PC1260 having stable performance in the field.

Package Includes:

  1. 1 x SKYRC PC1260 Dual Channel 12S LiPo Battery Charger
  2. 1 x AC Power Cord
  3. 1 x 12S Balance Adaptor
  4. 1 x Data cable
  5. 1 x Instruction Manual

SkyRC PC520 is an AC input LiPo charger for drones that can charge 6s LiPo batteries with balance charge mode and storage mode. It has short-circuit protection and reverse polarity protection for maximum safety. There is an LED digit on to indicate real-time data.


Features:

  1. Supports 6s LiPo battery Adjustable charge current from 1.0 to 20.0A
  2. The charger can store the charge current of the last charge program
  3. LED digits on indicate charge/discharge status
  4. Two working modes: balance charge mode and storage mode
  5. Maximum safety: short-circuit protection and reverse polarity protection

Specifications:

  1. Input Voltage:100-240V
  2. Output Power:520W
  3. Charger Current:1.0-20.0A
  4. LiPo Battery Cell Count:6S
  5. Working Mode: Balance Charge Mode/Storage Mode
  6. Size:220x142x65mm
  7. Weight:1.65kg

Package Includes:

1 x SKYRC PC520 LiPo Charger for Drones

1 x Connecting Cable

1 x User Manual

Do you want to build your own QUICK CHARGE power bank from your spare 18650 battery cells?  Then this 18650 5V 1A/2A Lithium Battery Digital Display Charging Module is for you. Just like a modern power bank, the module is equipped with Dual USB output to charge the gadgets at 2.1A and 1A. To charge the batteries, this module has two USB inputs one is C-type input, and the other is a MicroUSB input. Onboard, a brilliant blue-colored illuminating LED Display displays the real-time battery percentage in the 0–100% range, as well as the IN and OUT Signal. Furthermore, the board contains a connection for installing an LED to be used as a flashlight, which is generally found on a POWER BANK.

So, if you have any spare 18650 batteries cells in your scrap box, buy this module and create your own Power Bank, then share your DIY experience with us.

Caution: Pay attention to battery polarity while connecting it to the board, wrong polarity will burn the components 


Weight
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Output Voltage(V)

3V/5V

Output Port Type

USB or Expansion

Input Port

MicroUSB

Conversion Efficiency(%)

95 %

Length (mm)

100

Width (mm)

90

Height (mm)

20

Weight (gm)

71

Discharge Voltage Range (V)

5.40 – 35.00

Low Voltage Alert:

<5.2V

High Voltage Alert:

>35V

Maximum Discharge Power (W)

250

Dischage Current Range (A)

0.01 – 35.00

Current Consumption in Sleep Mode:

<100uA

Current Display Accuracy:

0.01-10.00A ±60mA 10.00-35.00A ±3%

Voltage Display Accuracy:

5.4-10V <80mV 10-20V <120mV 20-35V <160mV

Capacity Display Accuracy:

±3%

Dimensions (mm) LxWxH

136.6 x 104.8 x 107

Weight (gm)

879

Input Voltage (V AC)

100 ~ 240

Output Power(Watt)

1260W (630W x 2)

Discharge Power (W)

100 (50W x 2)

Charge Current (A)

1~ 12 x 2

Balance Current (A)

1.5

Battery Type

LiPo/LiHV

Battery Cell Count

12S

Working Mode

Balance Charge Mode Storage Mode Charge Mode

Length (mm)

272

Width (mm)

202

Height (mm)

119

Weight (Kg)

4.88