74HC21D,653 – Dual 4-Input AND Gate Surface Mount IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x 74HC21D,653 – Dual 4-Input AND Gate Surface Mount IC SMD-14 Package

L297 – 10V Stepper Motor Driver Controller IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x L297 – 10V Stepper Motor Driver Controller IC DIP-20 Package

FT245RL-REEL USB To Parallel FIFO Interface IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x FT245RL-REEL USB To Parallel FIFO Interface IC SMD-28 Package

MAX202EIM/TR RS-232 Interface IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x MAX202EIM/TR RS-232 Interface IC SMD-16 Package

The W5100S is a Hardwired TCP/IP embedded Ethernet Controller that enables easier Internet Connection for embedded Systems using SPI (Serial Peripheral Interface) and Parallel Bus.

W5100S suits users in need of stable Internet Connectivity Best, using a single chip to implement TCP/IP Stack, 10/100 Ethernet MAC, and PHY. The implemented Hardwired TCP/IP stack supports TCP, UDP, IPv4, ICMP, ARP, IGMP, and PPPoE which has been proven through various Applications over many years. W5100S uses a 16 Kbytes Internal Buffer as its Data Communication Memory.

By using W5100S, users can implement the Ethernet Application they need by using a simple socket Program instead of handling a complex Ethernet Controller. It is possible to use 4 independent hardware sockets simultaneously.

Features:

1. 48QFN lead-free package (7x7mm, 0.5mm pitch)
2. Host Interface: SPI (up to 70MHz, mode 0, 3) and Parallel System Bus with 2 Address signals and 8 Bits Data
3. Unattackable hardware engine for preventing network attacks such as flooding, spoofing, injection
4. 4 Independent hardware sockets simultaneously
5. supports various Internet Protocols: TCP, UDP, WOL over UDP, ICMP, IGMPv1/v2, IPv4, ARP, PPPoE
6. Internal 16 Kbytes memory for TCP/IP packet processing
7. socket-less commands possible: ARP request and ping requests
8. 10BaseT / 100Base TX Auto Negotiable Ethernet PHY Embedded
9. Auto-MDIX in auto-negotiation mode (Half/Full Duplex, 10/100 MBit/s speed)
10. IP fragmentation not supported, ARP-cache table will not be stored permanently
11. 3.3V operating voltage with 5V I/O signal tolerance
12. LED outputs (full/half duplex, link, 10/100 speed, active)
13. Reduced heat dissipation (W5500: 40℃ / other chips : 60-70℃)
14. Efficient power operation: power down & main clock gating as well as wake-on LAN over UDP

Specifications:

1. Ethernet: I/F PHY
2. Operating Temperature: -40 … + 85 °C
3. Operating Voltage: 3.3 V
4. Functions: 3-in-1, TCP/IP+MAC+PHY
5. Auto Negotiation: Yes
6. Network sockets count: 4
7. internal DPRAM buffer memory: 16 kB
8. Package :QFN
9. pin count: 48
10. auto MDIX: Yes
11. Wake on Lan: Yes
12. Power Down Mode: Yes
13. typ. Power Consumption: tbd
14. SPI (max. speed): 70 MHz
15. MCU I/F 8 bit (indirect),: SPI
16. PHY chip: W5100S
17. pin pitch: 0.50 mm
18. MII: No
19. Ethernet Speed: 10/100
20. parallel memory bus: 8bit indirect

Package Includes:

1 x WIZnet W5100S-Q

MCP2510-I/P CAN Controller Interface IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x MCP2510-I/P CAN Controller Interface IC DIP-18 Package