ADS1231IDR – 24-Bit 80SPS 1-Ch Delta-Sigma ADC IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x ADS1231IDR – 24-Bit 80SPS 1-Ch Delta-Sigma ADC IC SMD-16 Package

MCP3008 8-Channel 10-Bit A/D Converter with SPI Interface IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x MCP3008 8-Channel 10-Bit A/D Converter with SPI Interface IC DIP-16 Package

ICL7107CPLZ 3 1/2 Digit LED Driver with A/D Converter IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x ICL7107CPLZ 3 1/2 Digit LED Driver with A/D Converter IC DIP-40 Package

The CD4066B device is a quad bilateral switch intended for the transmission or multiplexing of analog or digital signals. It is pin-for-pin compatible with the CD4016B device but exhibits a much lower on-state resistance. In addition, the on-state resistance is relatively constant over the full signal-input range.

The CD4066B device consists of four bilateral switches, each with independent controls. Both the p and the n devices in a given switch are biased on or off simultaneously by the control signal. As shown in Figure 17, the well of the n-channel device on each switch is tied to either the input (when the switch is on) or to V_SS (when the switch is off). This configuration eliminates the variation of the switch-transistor threshold voltage with the input signal and, thus, keeps the on-state resistance low over the full operating-signal range.

The advantages over single-channel switches include peak input-signal voltage swings equal to the full supply voltage and more constant on-state impedance over the input-signal range. However, for sample-and-hold applications, the CD4016B device is recommended.

Features and Specifications:

1. 15-V Digital or ±7.5-V Peak-to-Peak Switching
2. 125-Ω Typical On-State Resistance for 15-V Operation
3. Switch On-State Resistance Matched to Within 5 Ω Over 15-V Signal-Input Range
4. On-State Resistance Flat Over Full Peak-to-Peak Signal Range
5. High On or Off Output-Voltage Ratio: 80 dB Typical at f_is = 10 kHz, R_L = 1 kΩ
6. High Degree of Linearity: <0.5% Distortion Typical at f_is = 1 kHz, V_is = 5-V_p-p V_DD – V_SS ≥ 10-V, R_L = 10 kΩ
7. Extremely Low Off-State Switch Leakage, Resulting in Very Low Offset Current and High Effective Off-State Resistance: 10 pA Typical at V_DD – V_SS = 10-V, T_A = 25°C
8. Extremely High Control Input Impedance (Control Circuit Isolated From Signal Circuit): 10¹² Ω Typical
9. Low Crosstalk Between Switches: –50 dB Typical at f_is = 8 MHz, R_L = 1 kΩ
10. Matched Control-Input to Signal-Output Capacitance: Reduces Output Signal Transients
11. Frequency Response, Switch On = 40 MHz Typical
12. 100% Tested for Quiescent Current at 20-V
13. 5-V, 10-V, and 15-V Parametric Ratings

Package Includes:

1 x CD4066-BE 20-V 1:1 (SPST) 4-channel analog switch IC

This TXB0104D 4-bit noninverting translator uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation between any of the 1.2-V, 1.5- V, 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes. VCCA must not exceed VCCB. When the OE input is low, all outputs are placed in the high-impedance state. To ensure the high-impedance state during power up or power down, OE must be tied to GND through a pulldown resistor The current sourcing capability of the driver determines the minimum value of the resistor. The TXB0104D device is designed so the OE input circuit is supplied by VCCA. This device is fully specified for partial power- down applications using I OFF. The I OFF circuitry disables the outputs, which prevents damaging current back-flow through the device when the device
is powered down.

Application:

1. Headsets
   
2. Smartphones
   
3. Tablet 
   
4. Desktop PC

Note: Actual product can vary from shown image

Features:

1. Low power consumption
2. I OFF supports partial power-down mode operation
3. Light weight
4. Compact size

Specifications:

1. Product: Voltage Level Translator Bidirectional
2. IC Model: TXB0104D
3. Supply Voltage: 1.2 V to 3.6
4. Packages: SOIC (14)
5. Dimension: 8.65 mm × 3.91 mm
6. Pins: 14
7. VCC isolation feature: if either VCC input ss at GND

Note: For more info refer to Datasheet

Packages Includes:

1 x TXB0104D Voltage Level Translator Bidirectional

DAC0800LCN/NOPB 8-Bit Digital to Analog D/A Converter IC

Note:

1. Product Images are shown for illustrative purposes only and may differ from the actual product.
2. For Technical Specifications about the IC go through the Datasheet in the Attachment section.
   

Package Includes:

1 x DAC0800LCN/NOPB 8-Bit Digital to Analog D/A Converter IC DIP-16 Package