DYS 20A Multi-Copter Brushless Speed Controller Programmable with 5V/2A BEC.  The ESC’s power input uses extremely low output resistance greatly enhances power stability and has a protective effect on the battery. Separately voltage regulator IC for the microprocessor. providing good anti-jamming capability. Using Simon K’s dedicated multi-copter program, and the master chip with high stability crystal oscillator, making the motor control more precise.

Note: Actual products may vary from the product images.

Features:

1. Drive tube and high-power Mos, and Mos tube plus a separate heat sink, Extreme low output resistance of the PCB(printed circuit board), super current endurance.
2. The power input uses extremely low output resistance greatly enhances the power stability and has a protective effect on the battery.
3. Safety electrical function: when the power is turned on, regardless of the throttle stick in any position does not start the motor immediately, to avoid personal injury.
4. Separately voltage regulator IC for the microprocessor. providing good anti-jamming capability.
5. Supported motor speed (Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
6. Using Simon K’s a dedicated multi-copter program tgy_debug, and the master chip with high stability crystal oscillator, making the motor control more precise.

Package Includes:

1 x DYS 20A Multi-copter Brushless Speed Controller

This is all down to a little device called an ESC, or (Electronic Speed Controller) This is what translates a pilot’s controls into precise instructions sent to the motors to control movement Electronic speed controllers (ESCs) are devices that allow drone flight controllers to control and adjust the speed of the aircraft’s electric motors. A signal from the flight controller causes the ESC to raise or lower the voltage to the motor as required, thus changing the speed of the propeller

An ESC or an Electronic Speed Controller controls the brushless motor movement or speed by activating the appropriate MOSFETs to create the rotating magnetic field so that the motor rotates. The higher the frequency or the quicker the ESC goes through the 6 intervals, the higher the speed of the motor will be,

Here, is the motor compatibility chart for this ESC,

Features:

1. Low Noise
2. Temperature and Interference
3. Fast Response
4. High Efficiency
5. For Compatibility
6. Please Leave A Note of Motor Type

Specifications: 

1. Voltage: 18V – 52.2V
2. Current: 80A
3. Peak Current: 100A
4. Stand by consumption: ≤50mA
5. BEC: NO
6. Throttler refresh Frequency: 1100 – 1940µs
7. Throttler Response speed: 300ms

Packages Includes:

1 x T Motor ALPHA 80A 12S ESC

When using a lithium battery pack of more than 3S, a switch‐mode BEC has much higher efficiency with lower heat. For a traditional linear BEC, Using a high-efficiency DC-DC voltage regulator chip, the conversion efficiency exceeds 90%.Has a working status indicator, which lights up when the UBEC is working normally. With input reverse connection protection, overcurrent protection, output short circuit protection, overheating protection and other functions, safe and reliable.

Features:

1. It adopted the advance regulator chip with conversion efficiency exceeding 90%
2. One output have 4 options for output voltage applicable for all kinds of receivers gyros servos
3. it featured input incorrect polarity protection

Package Includes:

1 x UBEC-8A+4A

This T-motor 200A 14S Flame Type ESC featured efficient and reasonable dissipation, layered structure. Compatible with U12 Motors and specially designed for multi-rotors. T Flame ESC can give a continuous current of 200A, and a peak current of up to 240A (10Sec).

Features:

1. High-performance microprocessor brings out the best compatibility with all kinds of motors and the highest driving efficiency.
2. The throttle range can be configured to be compatible with all transmitters currently available on market.
3. Smooth, linear, quick, and precise throttle response.
4. CNC Aluminum alloy enclosure, IP55 PCB with nanotechnology, widely used in UAV agriculture, search and rescue, etc.
5. Separate voltage regulator IC for the microprocessor to get a better anti-jamming capability.
6. Multiple protection features: Low-voltage cut-off protection / over-heat protection/throttle signal loss protection.
7. USB supported. The firmware of the ESC can be updated by the USB adapter.
8. Several kinds of Program Cards are supported. Very easy to program the ESC at home or at the field.

Specifications:

1. Continuous Current (A): 200
2. Peak Current (10sec): 240
3. BEC: N0
4. LIPO: 6-14s
5. Programmable: No

Package Includes:

1 x T motor Flame 200A 14S

An opto ESC isolates the high-power side (battery and motor) from the signal side (connection to the receiver) by internally transmitting the receiver throttle signal from the input side to the output side of the ESC through an opto-coupler.

ReadytoSky 30A 2-6S ESC is specifically made for quadcopters and multi-rotors. Which provides faster and better motor speed control giving better flight performance compared to other available ESCs.

ReadytoSky 30A 2-6 ESC comes with a multi-integrated special program, fast throttle response, surpasses all kinds of open-source software. Firmware was optimized specifically integrated circuitously for the disc motor, and it has very good compatibility and this ESC is compatible with 2-6s Lipo Battery.

Due to ultra-low resistance MOSFET, it has a strong flow capacity. With MOSFET special driver integrated circuit, its performance and stability far surpass the driving circuit with discrete components built.

If you are wandering to build a drone and don’t know what will be the best ESC for you then worry no more, we have got your back. At Robu, we have everything for you to get started with your drone project.

Features:

1. Specifically optimized firmware ESC, the ESC has a very good compatibility
2. Highly intelligent, adaptive ability, extremely easy to use
3. Throttle signal line is a twisted pair, copper wire to reduce cross-talk signal generated
4. Supports up to 621Hz refresh rates up to the throttle signal, compatible with a variety of flight control (Note: More than 500Hz signal of the throttle throttle are all non-standard signal)
5. Use MOSFET special driver chip, performance and stability far beyond the driving circuit with discrete components built

Specifications:

1. Model: 30A 2-6S ESC
2. Cont. Current: 30A
3. Max. Current: 40A
4. Voltage: 4 V-16.8V
5. Connector: Female-Banana connector
6. BEC : No (OPTO ESC)
7. Li-ion/Li0poly: 2-6S
8. Weight: 30g

Packages Includes:

1 x ReadytoSky 30A 2-6S ESC 3.5mm Banana connector

The Flame 80A HV V2 ESC by Tiger Motor provides professional-level power for large multi-rotor aircraft. The ESC is housed in a machined aluminum case providing both heat dissipation and protection.

Features:

1. High-performance microprocessor brings out the best compatibility with all kinds of motors and the highest driving efficiency.
2. The throttle range can be configured to be compatible with all transmitters currently available on market.
3. Smooth, linear, quick, and precise throttle response.
4. CNC Aluminum alloy enclosure, IP55 PCB with nanotechnology, widely used in UAV agriculture, search and rescue, etc.
5. Separate voltage regulator IC for the microprocessor to get a better anti-jamming capability.
6. Multiple protection features: Low-voltage cut-off protection / over-heat protection/throttle signal loss protection.
7. USB supported. The firmware of the ESC can be updated by the USB adapter.
8. Several kinds of Program Cards are supported. Very easy to program the ESC at home or at the field.

Specifications:

1. Output: Continuous 80A, Burst 105A up to 10 Secs.
2. Input Voltage: 6-12 cells lithium battery.
3. Refresh Rate: 600Hz
4. Protection: IP57
5. BEC: No
6. Signal Frequency: Up to 621Hz
7. Size: 77mm (L) x 35mm (W) x 18mm (H).
8. Weight: 94g.

Package Includes:

1 x T Motor FLAME 80A 12S V2.0 ESC