This is a TTGO T-Camera Plus 1.3 Inch Display Normal Rear Camera Module With OV2640. The module contains an IPS Panel ST7789/1.3 Inch display. It has an Integrated external SD card slot. The camera can be extended to become a rear camera, the program is set to delay the photo, and then become a camera function.

Features:

1. The external antenna is used to increase the Wi-Fi communication range.
2. The board comes with a microSD card slot.
3. This can be very useful to store photos, data collected from I2C sensors, or to store files.

Package Includes:

1 x TTGO T-Camera Plus Camera Module With OV2640 1.3 Inch Display Rear Camera Normal Rear Camera

The runcam LINK Digital FPV Air Unit is an advanced video transmission module that supports a 5.8 GHz digital video signal and 1280 x 720 60fps image transmission, with a transmission range of up to 4 km and a minimum end-to-end latency within 32 ms*. The air unit can be mounted on a racing drone and used with DJI FPV Goggles or a remote controller to transmit video, control signals, and light controller information wirelessly.

Features:

1. Digital FPV AIR UNIT Phoenix HD Camera Version
2. Embedded Remote Controller Receiver
3. the delay is as low as 32ms, which is suitable for freestyle flying.

Note: For more technical details go through Datasheet in the attachment section

Package Includes:

1 x RUNCAM-LINK air unit Phoenix HD camera

1 x IPEX Antenna

1 x JST SH 1.0 6 PIN Cable

1 x Manual guide

IMX219-160 8MP IR-CUT Camera, IR-CUT Infrared Night Vision, 162° FOV, Applicable For Compute Module / Jetson Nano / Jetson Xavier NXIMX219 Camera, with 800 megapixels and 160 FOV, IR-CUT infrared, compatible with Jetson nano. You can also use it with CM3/CM3+ expansion boards like Raspberry Pi Compute Module IO board, Compute Module IO Board Plus, Compute Module POE Board of Waveshare, and the Stereo Pi board. This camera integrates IR-CUT.

Connect the IO port on the board to GPIO, input a high level (3.3V) to turn off the infrared filter and set it to night vision mode, and input a low level (GND) to turn on the infrared filter and set it to daytime mode.
In the night vision mode, the reddish effect appears when taking pictures during the day, which is a normal phenomenon.

Features:

1. Suitable for AI applications
2. IR-CUT Infrared Night Vision
3. 800 megapixels and 160 FOV
4. Facial recognition, road mark recognition
5. Compatible With Raspberry Pi Compute Module CM3 / CM3+ / CM4

Package include:

1 X IMX219-160 IR-CUT Camera (with FFC)

1 X Infrared LED Board (B) 2 PCS

IMX219-200 Camera, Applicable For Jetson Nano, 8 Megapixels, 200°. You can also use it with CM3/CM3+ expansion boards like Raspberry Pi Compute Module IO board, Compute Module IO Board Plus, Compute Module POE Board of Waveshare and the Stereo Pi board.

Applications:

1. Combined with the Jetson Nano AI computer
2. Face recognition
3. Road mark detection
4. License plate recognition

Features:

1. Easy to use
2. Best for your IoT projects
3. Plug and play device
4. light weight

Package Include:

1 X IMX219-200 Camera

1 X 15-pin FFC (opposite sides contact)

The IMX290-83 IR-CUT Camera is a starlight camera for the Raspberry Pi board and module series. Using a Sony IMX290 starlight sensor with 2 million pixels, onboard IR-CUT, it can freely switch the modes between daytime (RGB) and nighttime (monochrome) through the onboard button. Direct Connect To Raspberry Pi Different Variants Including 4B/3B+/3A+/3B/2B/B+/A+, Extra FPC Cable Is Required For Zero / Zero 2 W Series

Feature:

1. Sensor IMX290
2. Starlight Camera
3. Clear Imaging Even In Low Light Conditions
4. Built-In IR-CUT for better imaging
5. Working With Raspberry Pi

Package Include:

1 X IMX290-83 IR-CUT Camera

1 X 15-pin FFC (opposite sides contact)

Features:

1. Object distance: 30cm
2. Resolution: 600LW/PH (Center)
3. Interface: USB 2.0

Package Includes:

1 x EMBEST Daughter Card, Digital Camera Module, 5MP USB Camera, 2592×1944 Resolution, Automatic Focus