This is a TTGO T-Camera Plus Camera Module OV2640 1.3 Inch Display Rear Camera Fish-eye Lens Rear Camera. The lens is used to transfer the image and data transmission. The module has a strong driving ability, strong anti-interference, low calorific value, and is more stable and reliable for Arduino projects. This module can be applied to Arduino Robot, Household Power Systems, raspberry pie, and DIY Servo Shield Module, etc.

Features:

1. The camera can be extended to become a rear camera.
2. This module can transfer images and data together.

Package Includes:

1 x TTGO T-Camera Plus Camera Module OV2640 1.3 Inch Display Rear Camera Fish-eye Lens Rear Camera

The runcam LINK Digital FPV Air Unit is an advanced video transmission module that supports a 5.8 GHz digital video signal and 1280 x 720 60fps image transmission, with a transmission range of up to 4 km and a minimum end-to-end latency within 32 ms*. The air unit can be mounted on a racing drone and used with DJI FPV Goggles or a remote controller to transmit video, control signals, and light controller information wirelessly.

Features:

1. Digital FPV AIR UNIT Phoenix HD Camera Version
2. Embedded Remote Controller Receiver
3. the delay is as low as 32ms, which is suitable for freestyle flying.

Note: For more technical details go through Datasheet in the attachment section

Package Includes:

1 x RUNCAM-LINK air unit Phoenix HD camera

1 x IPEX Antenna

1 x JST SH 1.0 6 PIN Cable

1 x Manual guide

IMX219-120 Camera, Applicable For Jetson Nano, 8 Megapixels, 120° FOV. IMX219 Camera, 8 megapixels and 120 FOV. Compatible with Jetson nano. You can also use it with CM3/CM3+ expansion boards like the official Compute Module IO board, Compute Module IO Board Plus, Compute Module POE Board of Waveshare, and the Stereo Pi board.

After the Bullseye version of the Raspberry Pi image, the underlying Raspberry Pi driver was switched from Raspicam to libcamera. libcamera is an open-source software stack (will be called driver later, which is easy to understand), which is convenient for third-party porting and development of their own camera drivers.

As of 2021-12-20, there are still many bugs in libcamera, and the current libcamera does not support python, so the Raspberry Pi official still provides a method for installing and downloading Raspicam. For users who are difficult to switch to libcamera but need to use the latest system, please directly refer to the Raspicam instructions.

Features:

1. Supports CM3/3+/4, Jetson Nano, Jetson Xavier NX
2. 8 Megapixels
3. Sensor: IMX219
4.  120 degree Field of view

Package Include:

1 X IMX219-120 Camera

1 X 15-pin FFC (opposite sides contact)

Raspberry Pi Camera Module, Fisheye Lens, Wider Field Of View After the Bullseye version of the Raspberry Pi image, the underlying Raspberry Pi driver was switched from Raspicam to lib-camera. lib-camera is an open-source software stack (will be called driver later, which is easy to understand), which is convenient for third-party porting and development of their own camera drivers. As of 2021-12-20, there are still many bugs in lib-camera, and the current lib-camera does not support python, so the Raspberry Pi official still provides a method for installing and downloading Raspicam. For users who are difficult to switch to lib-camera but need to use the latest system, please directly refer to the Raspicam instructions.

Features:

1. Raspberry Pi Camera
2. Supports all revisions of the Pi
3. Fisheye Lens, offers wider field of view
4. 5 megapixel OV5647 sensor
5. Adjustable focus distance
6. Best for IoT projects
7. Low power consumption

Package Include:

1 X RPi Camera (I)

1 X 15-pin FFC (opposite sides contact)

Raspberry Pi Camera Module, Embedded IR-CUT, Supports Night Vision, Type B. After the Bullseye version of the Raspberry Pi image, the underlying Raspberry Pi driver was switched from Raspicam to libcamera. libcamera is an open-source software stack (will be called driver later, which is easy to understand), which is convenient for third-party porting and development of their own camera drivers. As of 2021-12-20, there are still many bugs in libcamera, and the current libcamera does not support python, so the Raspberry Pi official still provides a method for installing and downloading raspicam. For users who are difficult to switch to libcamera but need to use the latest system, please directly refer to the Raspicam instructions.

Feature:

1. Raspberry Pi Camera, supports all revisions of the Pi
2. Embedded removable IR-CUT filter, eliminating color distortion in the daylight
3. Comes with infrared LED, supports night vision
4. 5 megapixel OV5647 sensor
5. Adjustable focus distance

Package Include:

1 X RPi IR-CUT Camera

2 X Infrared LED Board

1 X 15-pin FFC (opposite sides contact)

IMX219-160 8MP IR-CUT Camera, IR-CUT Infrared Night Vision, 162° FOV, Applicable For Compute Module / Jetson Nano / Jetson Xavier NXIMX219 Camera, with 800 megapixels and 160 FOV, IR-CUT infrared, compatible with Jetson nano. You can also use it with CM3/CM3+ expansion boards like Raspberry Pi Compute Module IO board, Compute Module IO Board Plus, Compute Module POE Board of Waveshare, and the Stereo Pi board. This camera integrates IR-CUT.

Connect the IO port on the board to GPIO, input a high level (3.3V) to turn off the infrared filter and set it to night vision mode, and input a low level (GND) to turn on the infrared filter and set it to daytime mode.
In the night vision mode, the reddish effect appears when taking pictures during the day, which is a normal phenomenon.

Features:

1. Suitable for AI applications
2. IR-CUT Infrared Night Vision
3. 800 megapixels and 160 FOV
4. Facial recognition, road mark recognition
5. Compatible With Raspberry Pi Compute Module CM3 / CM3+ / CM4

Package include:

1 X IMX219-160 IR-CUT Camera (with FFC)

1 X Infrared LED Board (B) 2 PCS