- 35% Off Industrial and Drone Parts.
- Free carbon neutral shipping on India orders ₹ 2000+.
End of Time:
:
:
:
0
0 items
₹0.00
No products in the cart.
- Lastest ESP32 Version: REV1
- Connectivity: WIFI & Bluetooth
- Memory: 4MB Flash4MB PSRAM
- Lithium battery interface, 500mA Max charging current
- Onboard TF CARD Slot
- Default firmware: Latest Micropython firmware
Add to Wishlist
Add to Wishlist
- ESP32 VCC range:2.2-3.6 V
- VBAT: direct to battery
- VCC: output of regulator 3.3V/600mA up to 250 mA during RF transmissions
- WiFi And Bluetooth Module
Add to Wishlist
Add to Wishlist
- Good Quality material
- 96-230Vac operating input range
- 50,000 hours MTBF
- 6-month warranty.
- Input Current: 0.5A maximum
- Input Power consumption (no load): 0.075W maximum
- USB-C connection goes straight into your Raspberry Pi
Add to Wishlist
Add to Wishlist
- 1.5 Meter Cable lead
- Micro USB Connector
- Input: 90~264 V AC @47/63 Hz
- Output: 5.2V, 2.5A
- Interchangeable heads for different countries
- 50,000 hours MTBF
Add to Wishlist
Add to Wishlist
- LoRa Spread Spectrum modulation technology
- Constant RF power output at + 20dBm-100mW voltage change
- High sensitivity: down to -148dBm
- Half-duplex SPI communication
- Programmable bit rates up to 300kbps
- Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
Add to Wishlist
Add to Wishlist
- Compatible with 3.3v or 5v I/O Arduino Board.
- Frequency Band: 433 MHZ (Pre-configure in factory)
- Low power consumption
- Compatible with Arduino Leonardo, Uno, Mega2560, DUE
- External Antenna via SMA Jack
Add to Wishlist
Add to Wishlist
- 168 dB maximum link budget.
- +20 dBm – 100 mW constant RF output vs.
- +14 dBm high-efficiency PA.
- Programmable bit rate up to 300 kbps.
- High sensitivity: down to -148 dBm.
- Bullet-proof front end: IIP3 = -12.5 dBm.
- Excellent blocking immunity.
- Low RX current of 10.3 mA, 200 nA register retention.
- Fully integrated synthesizer with a resolution of 61 Hz.
- FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
- Built-in bit synchronizer for clock recovery.
- Preamble detection.
- 127 dB Dynamic Range RSSI.
Add to Wishlist
Add to Wishlist
- Output voltage: +8.0V DC
- Minimum load current: 0.01A
- Nominal load current: 6.0A
- Maximum power: 48.0W
- Load regulation: ±5%
- Line regulation: ±5%
Add to Wishlist
Add to Wishlist
- Supply voltage 3.7V – 5V
- Mini and compact size
- Output power +20.8 dBm at 3.3V
- Sensitivity-116.5 dBm ~ -136 dBm
- ModulationLoRa, (G)FSK, (G)MSK, BPSK
Add to Wishlist
Add to Wishlist
- Communication distance: 15KM
- Sensitivity: down to -148dBm
- Programmable bit rates: up to 300kbps
- RSSI dynamic range: 127dB
- Wireless frequency: 433MHz
- Working voltage: 1.8-3.7v
- Working temperature: -40-+80 ℃
Add to Wishlist
Add to Wishlist
- Model No.:E32-900T30D
- Port Number:1
- Interface Type: CDMA
- Working Frequency Range:862 to 915 MHz
- Operating Distance Range (Meter):8000
Add to Wishlist
Add to Wishlist
- Fully compatible with High-Speed HDMI with Ethernet specification (Version 1.4).
- A superb cable with excellent audio-visual transfer properties that deliver signal without compromising purity and balance.
- Nickel-plated connectors for highest signal transfer rate and resistance in corrosion.
- A large gauge PVC jacket provides maximum shielding against wear and tear and extreme temperatures.
- Reinforced quad-layer braided shielding and Mylar-foil shielding provides utmost protection against RF and EM interference.
- Supports 480i, 480p, 720p, 1080i, 1080p, 1440p and 4K@60p resolution HDMI plug to HDMI plug leads
- Compatible with Raspberry Pi 4 Model B and all previous Raspberry Pi models
Add to Wishlist
Add to Wishlist
- Input Voltage DC 5V – 3A
- Processor Raspberry Pi 4 (Broadcom BCM2711, Quad-core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz)
- RAM: 4GB
- Storage: 64GB MicroSD Card
- Wi-Fi 2.4 GHz and 5.0 GHz IEEE 802.11ac wireless
- Bluetooth 5.0, BLE
- LoRaWAN Supports Class A, C
Add to Wishlist
Add to Wishlist
- Nickel Plated Connector Pins
- Fully triple shielded for increased noise immunity
- Length: 10cm
- 4Kp60 compliant
- 20Mohm 300VDC insulation withstands 300VDC for 0.1s
- Compatible with: Raspberry Pi Zero; Raspberry Pi Zero W; Raspberry Pi Zero W2
Add to Wishlist
Add to Wishlist
- Smart cities.
- Retail store sensors.
- Asset tracking.
- Max. Operating Voltage: 3.7.
- RF output: +22dBm.
- Programmable bit rate: 300kbps(FSK)/62.5K(LORA).
- Excellent blocking immunity.
- Low RX current: 8mA.
Add to Wishlist
Add to Wishlist
- min Supply voltage: 1.8.
- Max. Operating voltage: 3.7
- Min. Operational temperature range -20
- Max. Operational temperature: +70
- Max. RF Input Level:+10 d
Add to Wishlist
Add to Wishlist
Basic Components – Resistors | Capacitors | LEDs | Inductor | Varistor | Breadboard | Oscillator
Important links
Need Help?
+91 7231900002 (whatsapp)
Monday – Friday: 9:00-20:00
Saturady: 11:00 – 15:00
Customer Service
- -5% for all order in this week Shop now
- Free delivery for all orders over ₹ 2000