Level and Pressure Sensor
ACD10 infrared carbon dioxide sensor
Out of stock
ACM2000 Carbon Monoxide Sensor
Out of stock
Adafruit Accessories Muscle Sensor Surface EMG Electrodes – H124SG Covidien – Pack of 6
Out of stock
Adafruit LPS33HW Water Resistant Pressure Sensor – STEMMA QT RoHS Compliant
Out of stock
| Brand |
Adafruit |
|---|---|
| Product Type |
LPS33HW Water Resistant Pressure Sensor |
| Power Pins |
Vin 3Vo GND |
| Voltage(V) |
3-5V |
| I2C Logic pins: |
SCK – this is the I2C clock pin ,connect to your microcontrollers I2C clock line SDI – this is the I2C data pin ,connect to your microcontrollers I2C data line. |
| SPI Logic pins: |
SCK – This is also the SPI Clock pin ,its an input to the chip SDO – this is the Serial Data Out / Microcontroller In Sensor Out pin ,for data sent from the LPS35HW to your processor SDI – this is also the Serial Data In / Microcontroller Out Sensor In pin ,for data sent from your processor to the LPS35HW CS – this is the Chip Select pin ,drop it low to start an SPI transaction. Its an input to the chip |
| Support |
I2C or SP |
| Length (mm) |
2.5 |
| Width (mm) |
2 |
| Height (mm) |
0.5 |
| Weight (g) |
1g |
Adafruit MPRLS Ported Pressure Sensor Breakout – 0 to 25 PSI RoHS Compliant
Out of stock
| Brand |
Adafruit |
|---|---|
| Pressure Range (MPa) |
0 to 25 PSI |
| ADC |
24 bit |
| sensing gauge |
A silicone-gel covered pressure |
| Port |
The port is made of stainless steel and is 3.7mm long and 2.5mm diameter |
| Voltage (V) |
3.3V power regulation and level shifting |
| Address |
Uses I2C address 0x18 |
| Product Dimensions |
17.8mm x 16.7mm x 7.5mm / 0.7" x 0.7" x 0.3" |
| Product Weight |
1.1g / 0.0oz |
Adafruit MS8607 Pressure Humidity Temperature PHT Sensor – STEMMA QT / QwiicRoHS Compliant
Out of stock
Adafruit SGP30 Air Quality Sensor Breakout – VOC and eCO2 – STEMMA QT / QwiicRoHS Compliant
Out of stock
| Brand |
Adafruit |
|---|---|
| Model No. |
SGP30 Air Quality Sensor |
| Interface |
I2C |
| Accuracy |
15% |
| Element |
metal-oxide sensing |
| Voltage (V) |
3.3V or 5V |
| Power Pins |
Vin: this is the power pin. Since the sensor chip uses 3 VDC for logic ,we have included a voltage regulator on board that will take 3-5VDC and safely convert it down. To power the board ,give it the same power as the logic level of your microcontroller – e.g. for a 5V micro like Arduino ,use 5V 1V8: this is the 1.8V output from the voltage regulator ,you can grab up to 50mA from this if you like GND: common ground for power and logic |
| Data Pins |
SCL – I2C clock pin SDA – I2C data pin |
| Length (mm) |
2.5 |
| Width (mm) |
1.5 |
| Height (mm) |
0.5 |
| Weight (g) |
2 g |
ADP2000 Differential Pressure Sensor
Out of stock
ADP810 Differential Pressure Sensor
Out of stock
ADXL345, 3 Axis Accelerometer module
Out of stock
AFM0200 Micro Flow Sensor
Out of stock
AFM0725 Mass Flow Meter
Out of stock