- 35% Off Industrial and Drone Parts.
- Free carbon neutral shipping on India orders ₹ 2000+.
End of Time:
:
:
:
0
0 items
₹0.00
No products in the cart.
20×4 Alphanumeric LCD (Green)
In Stock
Add to Wishlist
Add to Wishlist
16×2 Alphanumeric LCD (Blue)
In Stock
Add to Wishlist
Add to Wishlist
20X4 Alphanumeric LCD (Blue)
In Stock
Add to Wishlist
Add to Wishlist
- Lastest ESP32 Version: REV1
- Connectivity: WIFI & Bluetooth
- Memory: 4MB Flash4MB PSRAM
- Lithium battery interface, 500mA Max charging current
- Onboard TF CARD Slot
- Default firmware: Latest Micropython firmware
Add to Wishlist
Add to Wishlist
- ESP32 VCC range:2.2-3.6 V
- VBAT: direct to battery
- VCC: output of regulator 3.3V/600mA up to 250 mA during RF transmissions
- WiFi And Bluetooth Module
Add to Wishlist
Add to Wishlist
- Operating voltage range:1.71V to 3.6V
- Power consumption @ 1.8V:0.55 mA (High) ,0.26 mA(Low)
- Smart FIFO up to 9 Kilobyte based on features set
- Embedded temperature sensor:16 bit
Add to Wishlist
Add to Wishlist
- LSM303D 6DoF Motion Sensor
- ±2/±4/±8/±12 gauss magnetic scale
- ±2/±4/±6/±8/±16 g linear acceleration
- 16-bit data output
- 3.3V or 5V compatible
- I2C interface, with address select via ADDR cuttable trace (0x1D or 0x1E)
- Reverse polarity protection
Add to Wishlist
Add to Wishlist
- Operating Voltage: 3.3V-5.5V
- Low Power Consumption
- High Accuracy
- I2C Communication
- Small Size
Add to Wishlist
Add to Wishlist
- Operating Voltage: 3.3V~5V
- Operating Current: 8~10uA
- Interface: Gravity-I2C
- I2C Address: 0x19 (default) / 0x18 (optional)
- User-selectable Scale: ±2g/±4g/±8g/±16g
- Operating Temperature: -40℃~+85℃
Add to Wishlist
Add to Wishlist
- Working Voltage: 3.3~5V
- Communication: Digital
- Connector: Gravity
Add to Wishlist
Add to Wishlist
- LoRa Spread Spectrum modulation technology
- Constant RF power output at + 20dBm-100mW voltage change
- High sensitivity: down to -148dBm
- Half-duplex SPI communication
- Programmable bit rates up to 300kbps
- Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
Add to Wishlist
Add to Wishlist
- Compatible with 3.3v or 5v I/O Arduino Board.
- Frequency Band: 433 MHZ (Pre-configure in factory)
- Low power consumption
- Compatible with Arduino Leonardo, Uno, Mega2560, DUE
- External Antenna via SMA Jack
Add to Wishlist
Add to Wishlist
- 168 dB maximum link budget.
- +20 dBm – 100 mW constant RF output vs.
- +14 dBm high-efficiency PA.
- Programmable bit rate up to 300 kbps.
- High sensitivity: down to -148 dBm.
- Bullet-proof front end: IIP3 = -12.5 dBm.
- Excellent blocking immunity.
- Low RX current of 10.3 mA, 200 nA register retention.
- Fully integrated synthesizer with a resolution of 61 Hz.
- FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
- Built-in bit synchronizer for clock recovery.
- Preamble detection.
- 127 dB Dynamic Range RSSI.
Add to Wishlist
Add to Wishlist
- 3-axis gravity accelerometer and 3-axis gyroscope
- On-chip temperature sensor
- Communication protocol I2C:0x68
- Accelerometer noise 100 μg/√Hz
- Gyroscope sensitivity error 1%
- Gyroscope noise ±4 mdps/√H
Add to Wishlist
Add to Wishlist
- Supply voltage 3.7V – 5V
- Mini and compact size
- Output power +20.8 dBm at 3.3V
- Sensitivity-116.5 dBm ~ -136 dBm
- ModulationLoRa, (G)FSK, (G)MSK, BPSK
Add to Wishlist
Add to Wishlist
- Operating Voltage: 3.3V
- Current Consumption: 140uA (sleep mode)/ 520uA (Accelerometer mode only)/ 4.27mA (Gyro mode only)/ 4.9mA (accelerometer and gyro mode)
- Initial Sensitivity: accelerometer ±1%; gyro ±1%
- Non-linear Sensitivity: accelerometer ±0.5%, gyro ±0.1%
- Interface: I2C/SPI(7MHz)
- Selectable Scale: ±2g/±4g/±8g/±16g
- Gyroscope Range: ±125/±250/±500dps
Add to Wishlist
Add to Wishlist
Basic Components – Resistors | Capacitors | LEDs | Inductor | Varistor | Breadboard | Oscillator
Important links
Need Help?
+91 7231900002 (whatsapp)
Monday – Friday: 9:00-20:00
Saturady: 11:00 – 15:00
Customer Service
- -5% for all order in this week Shop now
- Free delivery for all orders over ₹ 2000