-
Fast ShippingGet the Priority Shipping on Prepaid Orders
Prepaid Orders
-
Normal Shipping Get Normal Delivery (Surface) with Cash On Delivery
COD Orders
₹1,925.59 (Including tax)
Discount per Bulk Quantity
| Quantity | Discount | Price |
|---|---|---|
| 5 - 10 | 5% | ₹1,829.30 (Including tax) |
| 11 - 20 | 8% | ₹1,771.54 (Including tax) |
| 21 - 40 | 10% | ₹1,733.03 (Including tax) |
| 41 - 100 | 12% | ₹1,694.51 (Including tax) |
Out of stock
No worries! Enter your email, and we'll let you know as soon as it's back in stock.
Get the Priority Shipping on Prepaid Orders
Prepaid Orders
Get Normal Delivery (Surface) with Cash On Delivery
COD Orders
The NGM2611 is a pre-calibrated module for natural gas alarms which is precisely calibrated in Figaro’s humidity and temperature-controlled facility. The module uses TGS2611-E00 which incorporates a filter to eliminate the influence of interference gases such as alcohol, resulting in a highly selective response to methane. The most important process in manufacturing reliable residential gas alarms is adjusting the alarm point. Calibration is a complicated and time-consuming process that also requires a substantial investment in calibration equipment. By eliminating the costly calibration process, this module enables users to easily and simply manufacture residential natural gas alarms. Figaro has taken the complexity out of designing a gas detector circuit by providing users with a temperature compensation circuit that combines a built-in thermistor and individually adjusted load resistor together with Figaro’s low-power methane gas sensor.
Note: for more technical details go through Datasheet in the attachment section
1 x Figaro NGM2611-E13 Methane Sensor Module factory calibrated
| Circuit Voltage |
5.0±0.2V DC |
|---|---|
| Heater Current |
56±5mA |
| Operating conditions |
0Ëš~40ËšC ,30~95%RH |
| Temperature differential between inside and outside detector casing |
≤10˚C max. (NOTE 1) |
| Circuit current |
10mA (max) |
| Reference voltage |
1.0~4.0V DC (NOTE 2) |
Only logged in customers who have purchased this product may leave a review.
Shipping and Delivery Policy
1. Shipping Process:
2. Shipping Charges:
3. Order Tracking:
4. Delivery Address:
5. Delivery Issues:
6. No Return Policy for Opened/Soldered Products:
7. Refund Policy:
Out of stock
Out of stock
| Particle Measurement Range |
0.3~1.0μm; 1.0~2.5μm; 2.5~10μm |
|---|---|
| Particle Counting Efficiency |
50%@0.3μm ,98%@>=0.5μm |
| Resolution of Particle Mass Concentration |
1μg/mᶟ |
| Temperature Measurement Range |
0~99℃ |
| Temperature Measurement Resolution |
0.1℃ |
| Humidity Measurement Range |
0~99% |
| Humidity Measurement Resolution |
0.1% |
| Humidity Measurement Accuracy |
±2% |
| Single Response Time |
<1s |
| Comprehensive Response Time |
≤10s |
| DC Supply Voltage |
Typ: 5V Min: 4.5V Max: 5.5V |
| Working Current |
≤100mA |
| Standby Current |
≤200mA |
| Data Interface Level |
L<0.8V ,H>2.7V ,maximum level voltage 3.3V |
| Working Temperature Range |
10~50℃ |
| Working Humidity Range |
0~99% |
| Storage Temperature Range |
40~80℃ |
Out of stock
| Model |
DFRobot Gravity NH3 Sensor |
|---|---|
| Detection Gas |
Ammonia (NH3) |
| Detection range |
0~100ppm |
| Working Voltage |
3.3~5.5V DC |
| Working Current |
<5mA |
| Output Signal |
I2C ,UART (0~3V) ,analog voltage |
| Compatibility |
Arduino ,ESP32 ,Raspberry pi |
| Lifespan |
>2 years (in the air) |
| Working Humidity Range |
15~90%RH (non-condensing) |
| Working Temperature Range (°C) |
-20~50℃ |
| Product Dimensions |
37 x 32mm |
Out of stock
Out of stock
| Product Name |
Figaro TGS 2600 Air Quality Sensor |
|---|---|
| Input Voltage (V) |
5.0±0.2V AC/DC |
| Load Resistance |
variable 0.45kΩ min. |
| Heater Resistance (Ω) |
approx 83Ω at room temp. (typical) |
| Heater current (mA) |
42±4mA |
| Heater power consumption (mW) |
210 |
| Sensor Resistance (kΩ) |
10kΩ ~ 90kΩ in air |
| Sensitivity (change ratio of Rs) |
0.3~0.6 Rs (10ppm of H2)/ Rs air |
Out of stock
| Model No. |
TGS2610-C00 |
|---|---|
| Heater Current |
56±5mA |
| Heater Resistance |
approx 59Ω at room temp. |
| Heater Voltage |
5.0±0.2V DC |
| Load Resistance |
variable 0.45kΩ min |
| Sensing Principle |
MOS type |
| Circuit Voltage |
5.0±0.2V DC |
| Sensor Resistance |
1.0~10.0kΩ in 1800ppm iso-butane |
| Standard Package |
TO-5 metal can |
| Target Gases |
Butane ,LP gas |
| Test Gas Conditions |
iso-butane in air at 20±2˚C ,65±5%RH |
| Heater power consumption |
280mW VH = 5.0V DC |
Out of stock
Out of stock
No account yet?
Create an Account
Reviews
Clear filtersThere are no reviews yet.