This is a Waveshare 1.3 Inch OLED Display (A) module. It is a very high-contrast display with no backlight.  It is perfect when you need an ultra-small display. This module supports SPI/I2C communication interfaces. It supports various hardware platforms such as Raspberry Pi/Jetson Nano/Arduino/STM32.

Comparing to LCD, OLED screens are way more competitive, which has a number of advantages such as high brightness, self-emission, high contrast ratio, slim outline, wide viewing angle, wide temperature range, and low power consumption. This module provides 3 kinds of driver interfaces; they are 3-wire SPI, 4-wire SPI, and I2C interface.

Useful link:

To do Hardware and Software setup, please follow this tutorial.

Pin Definition:

1. VCC Power positive (3.3~5V power input)
2. GND Ground
3. NC NC
4. DIN Data input
5. CLK Clock signal input
6. CS Chip selection, low active
7. D/C Command signal, low level for command, high level for data
8. RES Reset signal, low active

Dimension

Features:

1. Better quality
2. The IIC address can be changed, it is convenient to use with different machines.
3. Four square holes are easy to install

Package Includes:

1 x 1.3 Inch OLED Display (A)

This is a general 1.5inch diagonal OLED display Module from Waveshare, 128×128 pixels monochrome dot matrix display module with 16 grayscales, and embedded controller communicating via SPI or I2C interface.

It is perfect when you need an ultra-small display. Comparing to LCD, OLED screens are way more competitive, which has a number of advantages such as high brightness, self-emission, high contrast ratio, slim outline, wide viewing angle, wide temperature range, and low power consumption. It is compatible with any 3.3V-5V microcontroller, such as Arduino.

The characteristics of this display module are high brightness, self-emission, high contrast ratio, slim/thin outline, wide viewing angle, wide temperature range, and low power consumption.

Useful link:

To do Hardware and Software setup, please follow this tutorial.

Features:

1. 128×128 high resolution.
2. 16 grayscale, the better display effect.
3. Supports SPI or I2C interface, configured via an onboard resistor.
4. Comes with development resources and a manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32).

Package Includes:

1 x 1.5inch OLED Module

1 x PH2.0 7Pin

It is suitable for flight control of Pixhawk, etc. and is used to display the status information of aircraft. This module is connected to Pixhawk’s I2C interface

Note: Actual product may vary from image in terms of Design, Color, Size.

Features:

1. Light weight
2. Display compatible with Pixhawk 2.4.8 PIX PX4 Flight Control
3. Easy to use
4. Plug and play device

Specifications:

1. Product: OSD OLED Display
2. Operating voltage: 3.3V-5V DC
3. Compatible: Pixhawk 2.4.8 PIX PX4 Flight Control
4. Working temperature: -30°C ~ 70°C
5. Display dimension: 2.5 x 1.4 x 0.1mm
6. Over all dimension: 3 x 2.7 x 0.3mm
7. Weight: 3g

Packages Includes:

1 x OSD OLED Display for Pixhawk 2.4.8 PIX PX4 Flight Control

1.51inch Transparent OLED, 128×64 Resolution, SPI/I2C Interfaces, Light Blue Color Display. 1.51inch Transparent OLED Module, 128×64 Resolution OLED Display, Light Blue Color Display. OLED Module Embedded Independent Driver Chip, Comes with examples for Raspberry Pi, Arduino, STM32, etc. OLED transparent module, full viewing angle . Adopts 4-wire SPI and I2C interface, better compatibility, and fast data rate. Provide online development resources (examples for Raspberry Pi/Arduino/STM32), please contact the seller to get them.

Useful link:

To do the Hardware setup, please follow this tutorial.
To do the Software setup, please follow this tutorial.

Features:

1. OLED transparent module, full viewing angle
2. Adopts 4-wire SPI and I2C interface, better compatibility, fast data rate
3. Comes with development resources (examples for Raspberry Pi/Arduino/STM32)

Package Includes:

1 x Waveshare 1.51inch OLED Blue Color Display

1 x PH2.0 7PIN cable

1 x Screws Pack

The Grove – OLED Yellow&Blue Display 0.96 (SSD1315) is a blue and yellow two-colour display with 128*64 resolution. Compared with LCDs, there are many advantages on OLED(Organic Light Emitting Diode) like self-emission, high contrast ratio, slim/thin outline, wide viewing angle and low power consumption. The display works on both 3.3V and 5V supply voltage. You can use either I2C or SPI interface to light up the display with your microcontroller to display words, images, and whatever you want.

Features: 

1. 3.3V/5V power supply compatible
2. Changeable I2C address
3. SPI available
4. Low power consumption
5. Yellow and Blue two-colour 128×64 pixels
6. High contrast, high brightness
7. Wide operating temperature range: -40℃ ~ +85 ℃

Specification:

1. Input voltage 3.3V / 5V
2. Output Voltage 0 ~ 2.3V
3. Pixels 128 x 64
4. Temperature Range -40℃ ~ +85 ℃
5. Interface I2C/SPI

Package Includes :

1 x SeeedStudio Grove OLED Yellow&Blue Display
1 x JST Cable

This is a Waveshare 1.3 Inch OLED Display (B) module. It is a very high-contrast display with no backlight.  It is perfect when you need an ultra-small display. This module supports SPI/I2C communication interfaces. It supports various hardware platforms such as Raspberry Pi/Jetson Nano/Arduino/STM32.

Comparing to LCD, OLED screens are way more competitive, which has a number of advantages such as high brightness, self-emission, high contrast ratio, slim outline, wide viewing angle, wide temperature range, and low power consumption. This module provides 3 kinds of driver interfaces; they are 3-wire SPI, 4-wire SPI, and I2C interface.

Useful link:

To do Hardware and Software setup, please follow this tutorial.

Pin Definition:

1.GND: Power ground
2.VCC: Power positive
3.SCL: Serial Clock Line
4.SDA: Serial Data wire.

Features:

1. Better quality 
2. The IIC address can be changed, it is convenient to use with different machines.
3. Four square holes are easy to install

Package Includes:

1 x 1.3 Inch OLED Display (B)