- 35% Off Industrial and Drone Parts.
- Free carbon neutral shipping on India orders ₹ 2000+.
End of Time:
:
:
:
0
0 items
₹0.00
No products in the cart.
- Lastest ESP32 Version: REV1
- Connectivity: WIFI & Bluetooth
- Memory: 4MB Flash4MB PSRAM
- Lithium battery interface, 500mA Max charging current
- Onboard TF CARD Slot
- Default firmware: Latest Micropython firmware
Add to Wishlist
Add to Wishlist
- ESP32 VCC range:2.2-3.6 V
- VBAT: direct to battery
- VCC: output of regulator 3.3V/600mA up to 250 mA during RF transmissions
- WiFi And Bluetooth Module
Add to Wishlist
Add to Wishlist
- Output: Continuous 40A, Burst 60A up to 10 Secs.
- Input Voltage: 2-6 cells lithium battery or 5-18 cells NiCd/NIMh battery.
- BEC: 3A / 5V (Switch mode).
- Max Speed: 210,000rpm for 2 Poles BLM, 70,000rpm for 6 poles BLM, 35,000rpm for 12 poles BLM. (BLM: Brushless Motor)
Add to Wishlist
Add to Wishlist
- Output: Continuous 60A, Burst 80A up to 10 Secs.
- Input Voltage: 2-6 cells lithium battery or 5-18 cells NiCd/NIMh battery.
- BEC: Pentium-60A: 3A / 5V (Switch mode).
- Max Speed: 210,000rpm for 2 Poles BLM, 70,000rpm for 6 poles BLM, 35,000rpm for 12 poles BLM. (BLM: Brushless Motor)
Add to Wishlist
Add to Wishlist
- LoRa Spread Spectrum modulation technology
- Constant RF power output at + 20dBm-100mW voltage change
- High sensitivity: down to -148dBm
- Half-duplex SPI communication
- Programmable bit rates up to 300kbps
- Supports FSK, GFSK, MSK, GMSK, LoRa and OOK modulation modes
Add to Wishlist
Add to Wishlist
- Compatible with 3.3v or 5v I/O Arduino Board.
- Frequency Band: 433 MHZ (Pre-configure in factory)
- Low power consumption
- Compatible with Arduino Leonardo, Uno, Mega2560, DUE
- External Antenna via SMA Jack
Add to Wishlist
Add to Wishlist
- 168 dB maximum link budget.
- +20 dBm – 100 mW constant RF output vs.
- +14 dBm high-efficiency PA.
- Programmable bit rate up to 300 kbps.
- High sensitivity: down to -148 dBm.
- Bullet-proof front end: IIP3 = -12.5 dBm.
- Excellent blocking immunity.
- Low RX current of 10.3 mA, 200 nA register retention.
- Fully integrated synthesizer with a resolution of 61 Hz.
- FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation.
- Built-in bit synchronizer for clock recovery.
- Preamble detection.
- 127 dB Dynamic Range RSSI.
Add to Wishlist
Add to Wishlist
- Support High Voltage (HV) Receivers
- Input voltage: 3.7V-27V
- Max current: 30A
- 18AWG silicone cable
- JST Plug
- Cable length 20cm
- Weight: 11g – With LED indicator lamp
Add to Wishlist
Add to Wishlist
- Continuous Current: 40A
- Burst Current: 55A (10 Sec.)
- BEC Mode: Linear Mode, 5V@3A
- Programmable: Yes
- Battery cell : Li-PO / NiMH
Add to Wishlist
Add to Wishlist
1 Output: Continuous 80A, Burst 100A up to 10 seconds.
2 Input Voltage: 2-6S Lipo, 5-18 cells NiMH.
3 BEC: 5A / 5V Switch mode BEC.
4 Refresh rate of the throttle signal: 50Hz to 432Hz.
5 Max Speed: 210000rpm for 2 Poles BLM, 70000rpm for 6 poles BLM, 35000rpm for 12 poles BLM.
(BLM = BrushLess Motor)
Add to Wishlist
Add to Wishlist
- Output: Continuous 50A
- Burst 65A up to 10 seconds.
- Input Voltage: 2-4S Lipo, 5-12 cells N
- BEC: 5A / 5V Switch mode BEC.
- The refresh the rate of the throttle signal: 50Hz to 432
Add to Wishlist
Add to Wishlist
- Output: Continuous 20A.
- Burst 25A up to 10 seconds.
- Input Voltage: 2-3S Lipo, 5-9 cells NiMH.
- BEC: 2A / 5V Linear mode BEC.
- Refresh rate of the throttle signal: 50Hz to 432Hz.
- Size: 42mm x 25mm x 8mm.
- Weight: 19g.
Add to Wishlist
Add to Wishlist
- Output: Continuous 20A, Burst 25A up to 10 seconds.
- Input Voltage: 2-3S Lipo, 5-9 cells NiMH.
- BEC: 2A / 5V Linear mode BEC.
- Refresh rate of the throttle signal: 50Hz to 432Hz.
- Size: 42mm x 25mm x 8mm.
- Weight: 19g.
Add to Wishlist
Add to Wishlist
- Model: Wp-1060-BRUSHED
- Voltage Range: 2-3S Lipo or 5-9 NiMH
- Resistance: Fwd 0.001Ω, Rev 0.002Ω
- BEC Output: 3A/5V (Linear Mode)
- PWM Frequency: 1KHz
Add to Wishlist
Add to Wishlist
- Input Voltage: 2-3S Lipo/5-9 Cell NiMH
- Cont./Peak Current: 80A/400A
- Power Rating Upto 80 Amps
- Battery Connector Type XT-60
- BEC Output: Switch Mode: 6V/7.4V@3A
- Battery Compatibility LiPo/NiMh
Add to Wishlist
Add to Wishlist
- Model: Wp-1060-BRUSHED
- Voltage Range: 2-3S Lipo or 5-9 NiMH
- Power Rating Upto 60 Amps
- Resistance: Fwd 0.001Ω, Rev 0.002Ω
- BEC Output: 3A/5V (Linear Mode)
- PWM Frequency: 1KHz
- Battery Compatibility LiPo/NiMh
- Battery Connector Type Tamiya Connector
- Motor Connector Type 4mm Bullet Classic Crimp Terminal
Add to Wishlist
Add to Wishlist
Basic Components – Resistors | Capacitors | LEDs | Inductor | Varistor | Breadboard | Oscillator
Important links
Need Help?
+91 7231900002 (whatsapp)
Monday – Friday: 9:00-20:00
Saturady: 11:00 – 15:00
Customer Service
- -5% for all order in this week Shop now
- Free delivery for all orders over ₹ 2000