Single Board Computer
LattePanda Delta 432 with Case & Streaming Cable & Touch Display
Out of stock
LattePanda V1- 4GB/64GB with Enterprise License
Out of stock
LattePanda Alpha 864s – Tiny Ultimate Windows / Linux Device
Out of stock
Jetson AGX Xavier H01 Kit with Jetson Xavier AGX processor, 32 TOPs, Wi-Fi, Aluminum case with cooling fan, pre-installed JetPack System
Out of stock
| Module |
Pre-installed Jetson AGX Xavier 32GB |
|---|---|
| Display |
1 x HDMI 2.0 (TYPE A) |
| Camera |
Esp.conn or USB Camera |
| Ethernet |
1 x Gigabit Ethernet Connector (10/100/1000) |
| M.2 Key |
E Wifi + Bluetooth |
| USB |
1 x USB 3.0; 2 x USB 3.0 Type A (Integrated USB 2.0); 1 x USB 2.0 Micro-AB |
| Misc. |
2 x SPI ,2 x I2C Link (+3.3V I/O); 1 x UART ,1x I2S (3.3V Level); 5 x GPIO |
| Fan |
1 x 12V PWM (default) or 1 x 5V PWM (optional) |
| POWER (VDC) |
: 9-19 |
| System |
Pre-installed Jetpack 4.6 OS |
reServer J2032 Edge AI Device with Jetson Xavier NX 16GB, 256GB
Out of stock
| Module |
NVIDIA® Jetson Xavier™ NX 16GB |
|---|---|
| AI Perf |
21 TOPS |
| GPU |
NVIDIA Volta architecture with 384 NVIDIA CUDA® cores and 48 Tensor cores |
| CPU |
6-core NVIDIA Carmel ARM®v8.2 64-bit CPU 6 MB L2 + 4 MB L3 |
| DL Accelerator |
2x NVDLA Engines |
| Vision Accelerator |
7-Way VLIW Vision Processor |
| Memory |
8 GB 128-bit LPDDR4x @ 51.2GB/s |
| Storage |
16 GB eMMC 5.1 |
| Co-processor |
Raspberry Pi® RP2040 32-Bit Dual ARM Cortex-M0+ @ 133MHz |
reComputer J202 – Dev Kit carrier Board for Jetson Nano/Xavier
Out of stock
reComputer J101 Dev Kit Carrier Board for Jetson Nano, With micro SD card slot
Out of stock
CY8CKIT-PSOC-024LP, PSOC Family Processor Modules with LCD Display Development Kit
Out of stock
ODROID-H3 Single Board Computer
Out of stock
| Model |
ODROID-H3 |
|---|---|
| Power |
DC jack : outer (negative) diameter 5.5mm ,inner(positive) diameter 2.1mm DC 14V ~ 20V (up to 60W) DC 15V/4A power adapter is recommended if you don’t use two 3.5“ HDDs DC 19V/7A power adapter is recommended if you two 3.5” HDDs together Power consumption: IDLE: ≃1..9W CPU Stress: ≃15W CPU+GPU Stress: ≃18W Power-off: ≃0.25W Suspend: ≃0.6W |
| Processor |
Intel Celeron N5105 Processor (10nm ,Quad-Core ,TDP 10W) H3+(N6005) : up to 3.3Ghz 4MB L2 Cache Intel UHD Graphics (24/32 EU up to 900MHz) |
| Memory |
2 x DDR4 1.2V SO-DIMM slots Dual Channel ,up to 2933 MT/s (DDR4-PC23400) Max memory capacity 64GB DDR3/DDR5 is not supported |
| Storage |
1 x eMMC connector (bootable and selectable on BIOS) Various eMMC modules can be purchased at the Hardkernel store 2 x SATA3 6Gbps 1 x M.2 slot (PCIe 3.0 x 4 ,supports NGFF-2280 cards) M.2 SATA SSD is not supported |
| Networking |
2 x GbE LAN ports (RJ45 ,supports 10/100/1000/2500 Mbps) Realtek RTL8125B Supports Wake-On-Lan LED indicators (Green: Link ,Amber: Traffic) |
| Audio |
1 x Audio out (3.5mm jack) 1 x Audio in (3.5mm jack) 1 x SPDIF out (ALC1200 ,HDA codec) * HDMI & DP have audio output too. |
| Video |
1 x DisplayPort 1.2 (up to 4K@60Hz) 1 x HDMI 2.0 (up to 4K@60Hz) Dual simultaneous display support |
| External I/O |
2 x USB 3.0 Host ports 2 x USB 2.0 Host ports 1 x Peripheral Expansion Header (24-pin ,2.54mm pitch) 1 x DC 5V ,1 x DC 3.3V ,5 x GND 1 x UART (TXD/RXD/RTS/CTS) 2 x I2C (SCL/SDA) 1 x External Power Button HDMI CEC ,5VA+ 3 x USB 2.0 All 3.3V I/O signal level |
| Other features |
Passive Heatsink BIOS Backup Battery Maintains system time and BIOS settings Power Button Reset Button System LEDs Indicators: – Red (PWR) – Solid light when DC power is supplied – Blue (left ,SLEEP) – turns off only when the system enters into suspend mode – Blue (right ,PMIC) – turns on only when the major power rails are working – Amber (SATA) – Flashes when SATA data transfers – Green (NVMe) – Flashes when NVMe data transfers Active Cooling Fan Connector (12V 4-pin ,PWM input + TACHO output) – Active Cooling Fan is optional – Connector (4-pin ,2.54mm pitch) |
| Form Factor |
110 x 110 x 47 mm Approx. |
ODROID-N2L with 4GByte RAM
Out of stock
| Processor |
Amlogic S922X Processor (12nm) Quad-core Cortex-A73(2.2Ghz) and Dual-core Cortex-A53(2Ghz) ARMv8-A architecture with Neon and Crypto extensions Mali-G52 GPU with 6 x Execution Engines (800Mhz) |
|---|---|
| Power |
1 x DC jack : outer (negative) diameter 5.5mm ,inner(positive) diameter 2.1mm 7.5V ~ 16V (Recommend range of input) – DC 12V/2A power adapter is recommendedPower consumption: – IDLE : ≃ 1.5W (Performance governor) ,1.3W(Conservative governor) – CPU Stress (Passive Heat-Sink) : ≃ 5.4W (@1908/2208MHz ,Stock) ,5.8W (@2016/2400MHz ,Overclock) – CPU Stress (Active Cooling-FAN) : ≃ 6.1W (@1908/2208MHz ,Stock) ,6.4W (@2016/2400MHz ,Overclock) – Power-Off : ≃ 0.2W |
| Memory |
LPDDR4 4GiB or 2GiB with 32-bit bus width Data rate: 3216 MT/s 1.1Volt low power design |
| Storage |
1 x eMMC connector (8G ,16G ,32G ,64G and 128G are available) 1 x microSD slot (DS/HS modes up to UHS-I SDR104) |
| Networking |
Optional WiFi or Ethernet USB adapters |
| Video |
1 x HDMI 2.0 (up to 4K@60Hz with HDR ,CEC ,EDID) – Although the +5V Power pin is able to supply a minimum of 300mA ,according to HDMI 2.0 specification ,a sink shall not draw more than 50mA of current from the +5V Power pin. |
| Audio |
1 x HDMI digital output |
| External I/O |
1 x USB 3.0 Host port 1 x USB 2.0 Host port 1 x Debug serial console (UART) 1 x MIPI DSI 4Lane (TBD) 1 x Peripheral Expansion Header (40-pin ,2.54mm pitch) – 2 x DC 5V ,2 x DC 3.3V ,1 x DC 1.8V ,8 x GND – 1 x SPI – 1 x UART – 2 x I2C – 25 x GPIO (Max) – 2 x ADC input (10bit ,1.8V Max) – All of I/O signal level is 3.3 Volt except for ADC input at max 1.8 Volt |
| Other features |
Built with a large passive heatsink System LEDS Indicators: – Red (PWR) – Solid light when DC power is connected – Blue (ALIVE) – Flashing like heartbeat while Kernel is running. Active Cooling Fan Connector (5V 2-pin) – Connector (2-pin ,1.25mm pitch) |
| Dimensions |
Dimensions including Fan heatsink: 69mm x 56mm x 22mm Dimensions including Tall heatsink: 69mm x 56mm x 32mm |
| Weight (gm) |
66g including a Tall heatsink |
ODROID-XU4Q Single Board Computer
Out of stock
| Processor |
Samsung Exynos5422 ARM® Cortex™-A15 Quad 2.0GHz/Cortex™-A7 Quad 1.4GHz |
|---|---|
| Memory |
2Gbyte LPDDR3 RAM PoP (750Mhz ,12GB/s memory bandwidth ,2x32bit bus) |
| 3D Accelerator |
Mali-T628 MP6 OpenGL ES 3.1 / 3.0 / 2.0 / 1.1 and OpenCL 1.2 Full profile |
| Audio |
HDMI Digital audio output. Optional USB sound card |
| USB3.0 Host |
SuperSpeed USB standard A-type connector x 2 port |
| USB2.0 Host |
HighSpeed USB standard A type connector x 1 port |
| Display |
HDMI 1.4a with a Type-A connector |
| Storage (Option) |
eMMC module socket : eMMC 5.0 Flash Storage (up to 64GByte) |
| MicroSD Card Slot |
up to 128GByte |
| Fast Ethernet LAN |
10/100/1000Mbps Ethernet with RJ-45 Jack ( Auto-MDIX support) |
| WiFi (Option) |
USB IEEE 802.11 ac/b/g/n 1T1R WLAN with Antenna (External USB adapter) |
| HDD/SSD SATA interface (Optional) |
SuperSpeed USB (USB 3.0) to Serial ATA3 adapter for 2.5″/3.5″ HDD and SSD storage |
| Power Input |
4.8Volt~5.2Volt (5V/4A Power supply is recommended) |
| System Software |
Ubuntu 16.04 + OpenGL ES + OpenCL on Linux Kernel 4.14 LTS Android 4.4.2 on Kernel LTS 3.10 Android 7.1 is available as a community driven OS development. Full source code is accessible via our Github. |
| Dimensions (L x W x H) mm |
83 x 58 x 20 |
| Weight (gm) |
38 (without cooler approx.) |
BeagleBone Black Industrial AM3358 ARM Cortex-A8, 512MB RAM, 4GB eMMC, USB Interface
Out of stock