Features:

The Power Management Board (PM Board) serves the purpose of a Power Module as well as a Power Distribution Board. In addition to providing regulated power to Pixhawk 4 and the ESCs, it sends information to the autopilot about battery’s voltage and current supplied to the flight controller and the motors.

Features:

1. Model: Pixhawk 4
2. Power: 1000mw
3. Frequency: 433 Mhz
4. Material: Composite Material
5. Weight: 62g
6. Board dimensions: 8 x 5 x 1mm

Packages Includes:

1 x Holybro Pixhawk 4 Power management board

Feature:

1. Flight Control Built-in OSD / BEC
2. Micro-SD Back-box
3. Built-in Current Sensor
4. F4 Processor (F405)
5. On-Board Video Filter (only can supply 5V to VTX and Camera)

Specification:

1. SPI Gyro IC268G
2. On-Board OSD (controllered by Betaflight, FC over SPI bus)
3. MicroSD Blackbox
4. Baro (BMP280)( default is closed,need to open in configuration,if not know how to open,contact with us)
5. F4 Processor (F405)
6. 5v3a SBEC
7. Built-in Current Sensor
8. On-Board Video Filter (only can supply 5V to VTX and Camera)

Package include:

1 x F4 Pro V2 V3.5 v3s Flight Control Built-in OSD / BEC

JHEMCU F4 NOXE V3 5V 10V BEC OSD Baro Flight Controller ARCO  was designed to give awesome flight performance based on tried and tested sensors whilst also providing unparalleled I/O capabilities in a small and extremely lightweight form-factor using a next-generation CPU

A flight controller (FC) is a small circuit board of varying complexity. Its function is to direct the RPM of each motor in response to input. A command from the pilot for the multi-rotor to move forward is fed into the flight controller, which determines how to manipulate the motors accordingly.

Every part of the drone is controlled by a flight controller. It moves the drone by changing the RPM of the motors. It is a control system that takes input from the sensors and makes the drone fly accordingly. This is a small computer board with various sensors which understand the movement of the craft. It has sensors like Gyroscope, Accelerometer, Barometer, and Magnetometer. According to the signal comes from the transceiver , it controls the motors and craft.

The board is rock solid and gives great performance with the HAKRC 20 A ESC, except that you have to switch the motors 1 & 2 to get the motor connections right. The barometer does not work great. Even though I packed a sponge above it, it starts bouncing hard when I switch on ALT hold mode. The OSD is the best and it works flawlessly, as does the VCC feed, whcih gives you the actual battery voltage reading through betalight. Else all great, good light and powerful board for a micro build.

Connection Diagram: 

Board Difference: 

Features:

1. Compact In size
2. Color: black
3. Easy to install
4. High performance flight controller module
5. very use to product

Specifications: 

1. Brand (trade name): JHEMCU
2. Model: F4 NOXE V3
3. Main control (MCU): STM32F411CEU6/100 MHz
4. Sensor: BMI 270/Gyro/Accel
5. Video Overlay (OSD): AT7456E
6. Barometer (Baro): Yes (Deluxe version only)
7. Black Box (Black Box): 16MB (Deluxe Edition only)
8. Input voltage: Input voltage: 2S-6S (7.4V-26V)
9. 5V-BEC: 5V/2.5A ± 0.1V
10. 10V-BEC: 10V/2A+0.1V
11. Receivers (receivers): ELRs (CRSF), TBS (CRSF), SBU, IBU, DS M2, DS MX
12. HD interface: yes
13. UART: UART 1, UART 2
14. LIC: IIC1
15. LED strip: yes
16. Buzzer (buzzer): support 5V active
17. ESC signal (ESC signal): PWM, Oneshot125, Oneshot42, Multishot,
18. Dail 150, Dail 300, Dail 600
19. USB: Micro USB
20. Current terminal] (current port): yes
21. Voltage sensor (voltage sensor): Yes
22. Dfu button (dfu button): Yes
23. Firmware (Firmware): Betaflight_4.3.0 JHEF 411.HEX
24. Mounting hole: 20 x 20 x 3mm
25. Size: 27 x 27 x 5mm
26. Weight (weight): 4.3g

Note: The BMI 270 gyroscope only supports 4.3.0 firmware. Please do not flash the other version firmware.

Packages Includes: 

1 x JHEMCU F4 NOXE V3  Flight Controller

The flight controller uses the data gathered by the sensors to calculate the desired speed for each of the four motors. The flight controller sends this desired speed to the Electronic Speed Controllers (ESC’s), which translates this desired speed into a signal that the motors can understand.

The MPU6500 is the most widely used IMU sensor, and it’s used in nearly all of the greatest flight controllers. The reason for this is that it has a high vibration tolerance and can sample the gyro at 8kHz over an SPI interface.

Note: Product can vary from images in terms of Color and Design 

Features:

1. High performance & efficient flight controller & ESC
2. Light weight, Easy to connect
3. Compact in size
4. Flight controller comes with ARM processor
5. Compact size
6. Easy to Connect

Specifications:

1. Model: F7 MINI V1.0
2. Main control chip: ARM STM32F722RET6
3. Input voltage: 3-6S Lipo
4. SPI Gyro: MPU6500
5. Barometer: BMP280
6. Power Port: 1 C-Type
7. Firmware: AOCODAF722MINI
8. Weight: 6g
9. Dimensions: 3 x 3 x 1 mm

Packages Includes:

1 x F7 MINI V1.0 Flight Controller for Huafei

The Pixhawk 6C FC combined with the PM07 12S Power Module + M8N GPS brings tons of power to the autopilot and makes it super easy to power and locate the multirotor.

Pixhawk 6C Flight Controller Module

The Pixhawk 6C is the latest update to the successful family of Pixhawk flight controllers, based on the Pixhawk FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot pre-installed. Inside the Pixhawk 6C, you can find a STMicroelectronics based STM32H743, paired with sensor technology from Bosch & InvenSense, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications.

The Pixhawk 6C’s H7 microcontroller contains the Arm Cortex-M7 core running up to 480 MHz and has 2MB flash memory and 1MB RAM. Thanks to the updated processing power, developers can be more productive and efficient with their development work, allowing for complex algorithms and models. The FMUv6C open standard includes high-performance, low-noise IMUs on board, designed to be cost-effective while having IMU redundancy. A vibration isolation System to filter out high-frequency vibration and reduce noise to ensure accurate readings, allowing vehicles to reach better overall flight performances.

Features:

1. The Power Module comes completely assembled with XT60 connectors
2. New cost-effective design with low-profile form factor
3. Redundant inertial measurement unit (IMU) from Bosch & InvenSense
4. Newly designed integrated vibration isolation system to filter out high frequency vibration and reduce noise to ensure accurate readings
5. IMUs are temperature-controlled by onboard heating resistors, allowing optimum working temperature of IMUs
6. Lightweight & low power consumption

Packages Includes:

1 x Holybro Pixhawk 6C PM07 M8N