Single Board Computer
ODROID-H3 Single Board Computer
Out of stock
| Model |
ODROID-H3 |
|---|---|
| Power |
DC jack : outer (negative) diameter 5.5mm ,inner(positive) diameter 2.1mm DC 14V ~ 20V (up to 60W) DC 15V/4A power adapter is recommended if you don’t use two 3.5“ HDDs DC 19V/7A power adapter is recommended if you two 3.5” HDDs together Power consumption: IDLE: ≃1..9W CPU Stress: ≃15W CPU+GPU Stress: ≃18W Power-off: ≃0.25W Suspend: ≃0.6W |
| Processor |
Intel Celeron N5105 Processor (10nm ,Quad-Core ,TDP 10W) H3+(N6005) : up to 3.3Ghz 4MB L2 Cache Intel UHD Graphics (24/32 EU up to 900MHz) |
| Memory |
2 x DDR4 1.2V SO-DIMM slots Dual Channel ,up to 2933 MT/s (DDR4-PC23400) Max memory capacity 64GB DDR3/DDR5 is not supported |
| Storage |
1 x eMMC connector (bootable and selectable on BIOS) Various eMMC modules can be purchased at the Hardkernel store 2 x SATA3 6Gbps 1 x M.2 slot (PCIe 3.0 x 4 ,supports NGFF-2280 cards) M.2 SATA SSD is not supported |
| Networking |
2 x GbE LAN ports (RJ45 ,supports 10/100/1000/2500 Mbps) Realtek RTL8125B Supports Wake-On-Lan LED indicators (Green: Link ,Amber: Traffic) |
| Audio |
1 x Audio out (3.5mm jack) 1 x Audio in (3.5mm jack) 1 x SPDIF out (ALC1200 ,HDA codec) * HDMI & DP have audio output too. |
| Video |
1 x DisplayPort 1.2 (up to 4K@60Hz) 1 x HDMI 2.0 (up to 4K@60Hz) Dual simultaneous display support |
| External I/O |
2 x USB 3.0 Host ports 2 x USB 2.0 Host ports 1 x Peripheral Expansion Header (24-pin ,2.54mm pitch) 1 x DC 5V ,1 x DC 3.3V ,5 x GND 1 x UART (TXD/RXD/RTS/CTS) 2 x I2C (SCL/SDA) 1 x External Power Button HDMI CEC ,5VA+ 3 x USB 2.0 All 3.3V I/O signal level |
| Other features |
Passive Heatsink BIOS Backup Battery Maintains system time and BIOS settings Power Button Reset Button System LEDs Indicators: – Red (PWR) – Solid light when DC power is supplied – Blue (left ,SLEEP) – turns off only when the system enters into suspend mode – Blue (right ,PMIC) – turns on only when the major power rails are working – Amber (SATA) – Flashes when SATA data transfers – Green (NVMe) – Flashes when NVMe data transfers Active Cooling Fan Connector (12V 4-pin ,PWM input + TACHO output) – Active Cooling Fan is optional – Connector (4-pin ,2.54mm pitch) |
| Form Factor |
110 x 110 x 47 mm Approx. |
ODROID-H3+ Single Board Computer
Out of stock
| Processor |
Intel Celeron N6005 Processor (10nm ,Quad-Core ,TDP 10W) H3+(N6005) : up to 3.3Ghz 4MB L2 Cache Intel UHD Graphics (24/32 EU up to 900MHz) |
|---|---|
| Networking |
2 x GbE LAN ports (RJ45 ,supports 10/100/1000/2500 Mbps) Realtek RTL8125B Supports Wake-On-Lan LED indicators (Green: Link ,Amber: Traffic |
| Memory |
2 x DDR4 1.2V SO-DIMM slots Dual Channel ,up to 2933 MT/s (DDR4-PC23400) Max memory capacity 64GB DDR3/DDR5 are not supported |
| Storage |
1 x eMMC connector (bootable and selectable on BIOS) Various eMMC modules can be purchased at the Hardkernel store 2 x SATA3 6Gbps ( SATA Port-Multiplier is NOT compatible ) 1 x M.2 slot (PCIe 3.0 x 4 ,supports NGFF-2280 cards) M.2 SATA SSD is not supported |
| Video |
1 x DisplayPort 1.2 (up to 4K@60Hz) 1 x HDMI 2.0 (up to 4K@60Hz) Dual simultaneous display support |
| Audio |
1 x Audio out (3.5mm jack) 1 x Audio in (3.5mm jack) 1 x SPDIF out (ALC1200 ,HDA codec) * HDMI & DP have audio output too. |
| External I/O |
2 x USB 3.0 Host ports 2 x USB 2.0 Host ports 1 x Peripheral Expansion Header (24-pin ,2.54mm pitch) – 1 x DC 5V ,1 x DC 3.3V ,5 x GND – 1 x UART (TXD/RXD/RTS/CTS) – 2 x I2C (SCL/SDA) – 1 x External Power Button – HDMI CEC ,5VA+ – 3 x USB 2.0 – All 3.3V I/O signal level |
| Other features |
Passive Heatsink BIOS Backup Battery – Maintains system time and BIOS settings Power Button Reset Button System LEDS Indicators: – Red (PWR) – Solid light when DC power is supplied – Blue (left ,SLEEP) – turns off only when the system enters into suspend mode – Blue (right ,PMIC) – turns on only when the major power rails are working – Amber (SATA) – Flashes when SATA data transfers – Green (NVMe) – Flashes when NVMe data transfers Active Cooling Fan Connector (12V 4-pin ,PWM input + TACHO output) – Active Cooling Fan is optional – Connector (4-pin ,2.54mm pitch) |
| Power |
DC jack : outer (ground) diameter 5.5mm ,inner(positive) diameter 2.1mm DC 14V ~ 20V (up to 60W) – DC 15V/4A power adapter is recommended if you don’t use two 3.5“ HDDs – DC 19V/7A power adapter is recommended if you two 3.5” HDDs together Power consumption: – IDLE : ≃1..9W – CPU Stress : ≃15W – CPU+GPU Stress : ≃18W – Power-off : ≃0.25W – Suspend : ≃0.6W |
| Form Factor |
110mm x 110mm x 47mm Approx. |
ODROID-M1 with 4GByte RAM
Out of stock
| POWER |
1 x DC jack : outer (negative) diameter 5.5mm ,inner (positive) diameter 2.1mm DC input : 7.5V ~ 15.5V – DC 12V/2A power adapter is recommended – IDLE : ≃ 1.25W – CPU Stress : ≃ 4.44W (Performance governor) – Power Off : ≃ 0W |
|---|---|
| FORM FACTOR |
Board Dimensions: 90mm x 122mm x 16mm Heatsink Dimensions: 100mm x 123mm x 19mm Weight: 253 g including heatsink |
| PROCESSOR |
Rockchip RK3568 Processor L1 instruction cache: 32 KB ,4-way set associative (128 sets) ,64 byte lines ,shared by 1 processor L1 data cache: 32 KB ,4-way set associative (128 sets) ,64 byte lines ,shared by 1 processor L3 data cache: 512KB ,16-way set associative (512 sets) ,64 byte lines ,shared by 4 processorsQuad-Core Cortex-A55 (1.992GHz) ARMv8-A architecture with Neon and Crypto extensions Mali-G52 MP2 GPU with 4 x Execution Engines (650Mhz) |
| NPU |
0.8Tops@INT8 ,integrated high-performance AI accelerator RKNN NPU Supports one-click switching of Caffe/TensorFlow/TFLite/ONNX/PyTorch/Keras/Darknet |
| MEMORY |
4 or 8GiB LPDDR4 with 32-bit bus width Data rate: 3120 MT/s ,up to 1 ,560MHz |
| STORAGE |
1 x eMMC slot 1 x Micro SD slot (DS/HS mode up to UHS-I SDR104) 1 x NVME M.2 SSD (PCIe 3.0 x 2) 1 x SATA3.0 |
| NETWORKING |
1 x GbE LAN ports (RJ45 ,supports 10/100/1000 Mbps) – Realtek RTL8211F (Ethernet transceiver) – LED indicators * Green LED: Flashing by data traffics at 100Mbps connection * Amber LED: Flashing by data traffics at 1000Mbps connection |
| VIDEO |
1 x HDMI 2.0 (up to 4K@60Hz with HDR ,EDID) 1 x MIPI-DSI (works with 800 x 1280 LCD) |
| AUDIO |
1 x 3.5mm phone jack 1 x mono speaker output 1 x HDMI sound |
| EXTERNAL I/O |
2 x USB 2.0 host port 2 x USB 3.0 host port (or 1 x USB 3.0 host + 1 x USB 2.0 OTG port) 1 x Debug serial console (UART ,1.5Mbps N81) 1 x SATA Connector 1 x MIPI-CSI Camera Interface (15 pin) 1 x MIPI-DSI LCD Interface (31 pin) 1 x 40pin GPIO header |
ODROID-N2L with 2GByte RAM
Out of stock
ODROID-N2L with 4GByte RAM
Out of stock
| Processor |
Amlogic S922X Processor (12nm) Quad-core Cortex-A73(2.2Ghz) and Dual-core Cortex-A53(2Ghz) ARMv8-A architecture with Neon and Crypto extensions Mali-G52 GPU with 6 x Execution Engines (800Mhz) |
|---|---|
| Power |
1 x DC jack : outer (negative) diameter 5.5mm ,inner(positive) diameter 2.1mm 7.5V ~ 16V (Recommend range of input) – DC 12V/2A power adapter is recommendedPower consumption: – IDLE : ≃ 1.5W (Performance governor) ,1.3W(Conservative governor) – CPU Stress (Passive Heat-Sink) : ≃ 5.4W (@1908/2208MHz ,Stock) ,5.8W (@2016/2400MHz ,Overclock) – CPU Stress (Active Cooling-FAN) : ≃ 6.1W (@1908/2208MHz ,Stock) ,6.4W (@2016/2400MHz ,Overclock) – Power-Off : ≃ 0.2W |
| Memory |
LPDDR4 4GiB or 2GiB with 32-bit bus width Data rate: 3216 MT/s 1.1Volt low power design |
| Storage |
1 x eMMC connector (8G ,16G ,32G ,64G and 128G are available) 1 x microSD slot (DS/HS modes up to UHS-I SDR104) |
| Networking |
Optional WiFi or Ethernet USB adapters |
| Video |
1 x HDMI 2.0 (up to 4K@60Hz with HDR ,CEC ,EDID) – Although the +5V Power pin is able to supply a minimum of 300mA ,according to HDMI 2.0 specification ,a sink shall not draw more than 50mA of current from the +5V Power pin. |
| Audio |
1 x HDMI digital output |
| External I/O |
1 x USB 3.0 Host port 1 x USB 2.0 Host port 1 x Debug serial console (UART) 1 x MIPI DSI 4Lane (TBD) 1 x Peripheral Expansion Header (40-pin ,2.54mm pitch) – 2 x DC 5V ,2 x DC 3.3V ,1 x DC 1.8V ,8 x GND – 1 x SPI – 1 x UART – 2 x I2C – 25 x GPIO (Max) – 2 x ADC input (10bit ,1.8V Max) – All of I/O signal level is 3.3 Volt except for ADC input at max 1.8 Volt |
| Other features |
Built with a large passive heatsink System LEDS Indicators: – Red (PWR) – Solid light when DC power is connected – Blue (ALIVE) – Flashing like heartbeat while Kernel is running. Active Cooling Fan Connector (5V 2-pin) – Connector (2-pin ,1.25mm pitch) |
| Dimensions |
Dimensions including Fan heatsink: 69mm x 56mm x 22mm Dimensions including Tall heatsink: 69mm x 56mm x 32mm |
| Weight (gm) |
66g including a Tall heatsink |
ODROID-XU4Q Single Board Computer
Out of stock
| Processor |
Samsung Exynos5422 ARM® Cortex™-A15 Quad 2.0GHz/Cortex™-A7 Quad 1.4GHz |
|---|---|
| Memory |
2Gbyte LPDDR3 RAM PoP (750Mhz ,12GB/s memory bandwidth ,2x32bit bus) |
| 3D Accelerator |
Mali-T628 MP6 OpenGL ES 3.1 / 3.0 / 2.0 / 1.1 and OpenCL 1.2 Full profile |
| Audio |
HDMI Digital audio output. Optional USB sound card |
| USB3.0 Host |
SuperSpeed USB standard A-type connector x 2 port |
| USB2.0 Host |
HighSpeed USB standard A type connector x 1 port |
| Display |
HDMI 1.4a with a Type-A connector |
| Storage (Option) |
eMMC module socket : eMMC 5.0 Flash Storage (up to 64GByte) |
| MicroSD Card Slot |
up to 128GByte |
| Fast Ethernet LAN |
10/100/1000Mbps Ethernet with RJ-45 Jack ( Auto-MDIX support) |
| WiFi (Option) |
USB IEEE 802.11 ac/b/g/n 1T1R WLAN with Antenna (External USB adapter) |
| HDD/SSD SATA interface (Optional) |
SuperSpeed USB (USB 3.0) to Serial ATA3 adapter for 2.5″/3.5″ HDD and SSD storage |
| Power Input |
4.8Volt~5.2Volt (5V/4A Power supply is recommended) |
| System Software |
Ubuntu 16.04 + OpenGL ES + OpenCL on Linux Kernel 4.14 LTS Android 4.4.2 on Kernel LTS 3.10 Android 7.1 is available as a community driven OS development. Full source code is accessible via our Github. |
| Dimensions (L x W x H) mm |
83 x 58 x 20 |
| Weight (gm) |
38 (without cooler approx.) |
reComputer J101 Dev Kit Carrier Board for Jetson Nano, With micro SD card slot
Out of stock
reComputer J1010 Edge AI Device with Jetson Nano module, M.2 Key E Slot, Type-C connectors, Aluminium case, pre-installed JetPack System
Out of stock
| GPU |
NVIDIA Maxwell™ architecture with 128 NVIDIA CUDA® cores 0.5 TFLOPs (FP16) |
|---|---|
| Display |
HDMI 2.0 or DP1.2 ,eDP 1.4 ,DSI (1 x2) 2 simultaneous |
| Camera |
12 lanes (3×4 or 4×2) MIPI CSI-2 DPHY 1.1 (18 Gbps) |
| I/O Ports |
1x SDIO / 2x SPI / 4x I2C / 2x I2S / GPIOs -> I2C ,I2S |
| Connectivity |
(M.2 Key M)10/100/1000 BASE-T Ethernet |
| Video encoder |
1x 4K @ 30 (HEVC) ,250 MP/sec ,2x 1080p @ 60 (HEVC) ,4x 1080p @ 30 (HEVC) |
| Video decoder |
2x 4K @ 30 (HEVC) ,4x 1080p @ 60 (HEVC) ,500 MP/sec |
| UPHY |
1 x1/2/4 PCIE ,1x USB 3.0 ,3x USB 2.0 |
| Mechanical |
260-pin edge connector |
reComputer J1020 Edge AI Device with Jetson Nano module, Aluminium case, pre-installed JetPack System
Out of stock
reComputer J2012 Edge AI Device with Jetson Xavier NX 16 GB module, Aluminium case, pre-installed JetPack System
Out of stock
| CPU |
6-core NVIDIA Carmel ARM®v8.2 64-bit CPU 6MB L2 + 4MB L3 |
|---|---|
| GPU |
384-core NVIDIA Volta™ GPU with 48 Tensor Cores |
| Storage |
16 GB eMMC 5.1 Flash |
| Memory |
16 GB 128-bit LPDDR4x 59.7GB/s |
| Display |
2 multi-mode DP 1.4/eDP 1.4/HDMI 2.0 |
| Camera |
14 lanes (3×4 or 6×2) MIPI CSI-2 ,D-PHY 1.2 (up to 30 Gbps) ,Up to 6 cameras (24 via virtual channels) |
| Power |
10 W ,15 W ,20 W |
| AI Performance |
21 TOPS |
| DL Accelerator |
2x NVDLA Engines |
| Vision Accelerator |
7-Way VLIW Vision Processor |
| PCIe |
1 x1 (PCIe Gen3) + 1 x4 (PCIe Gen4) ,total 144 GT/s* |
| Video encoder |
2x 4K60 ,4x 4K30 ,10x 1080p60 ,20x 1080p30 (H.264) ,2x 4K60 ,4x 4K30 ,10x 1080p60 ,22x 1080p30 (H.265) |
| Video decoder |
2x 4K60 ,6x 4K30 ,10x 1080p60 ,22x 1080p30 (H.264) ,2x 8K30 ,6x 4K60 ,12x 4K30 ,22x 1080p60 ,44x 1080p30 (H.265) |
| Mechanical |
260-pin SO-DIMM connector 69.6 mm x 45 mm |
| Networking |
10/100/1000 BASE-T Ethernet |
| Length (mm) |
103 |
| Width (mm) |
90.5 |
| Height (mm) |
31 |
| Weight (g) |
150 |
reComputer J202 – Dev Kit carrier Board for Jetson Nano/Xavier
Out of stock